EPM2210F256C4 Altera, EPM2210F256C4 Datasheet - Page 18

• Manufacturer Part Number: EPM2210F256C4
• Description: IC MAX II CPLD 2210 LE 256-FBGA
• Manufacturer: Altera
• Series: MAX® IIr

Specifications of EPM2210F256C4

• Programmable Type: In System Programmable
• Delay Time Tpd(1) Max: 7.0ns
• Voltage Supply - Internal: 2.5V, 3.3V
• Number Of Logic Elements/blocks: 2210
• Number Of Macrocells: 1700
• Number Of I /o: 204
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 256-FBGA
• Voltage: 2.5V, 3.3V
• Memory Type: FLASH
• Number Of Logic Elements/cells: 2210
• Family Name: MAX II
• # Macrocells: 1700
• Frequency (max): 2.3148GHz
• Propagation Delay Time: 9.1ns
• Number Of Logic Blocks/elements: 221
• # I/os (max): 204
• Operating Supply Voltage (typ): 2.5/3.3V
• In System Programmable: Yes
• Operating Supply Voltage (min): 2.375V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 256
• Package Type: FBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 544-1340; EPM2210F256C4

2–10
Figure 2–8. LE in Dynamic Arithmetic Mode
Note to
(1) The addnsub signal is tied to the carry input for the first LE of a carry chain only.
MAX II Device Handbook
LAB Carry-In
Carry-In0
Carry-In1
Figure
data1
data2
data3
(LAB Wide)
addnsub
2–8:
(1)
The other two LUTs use the data1 and data2 signals to generate two possible carry-out
signals: one for a carry of 1 and the other for a carry of 0. The carry-in0 signal acts
as the carry-select for the carry-out0 output and carry-in1 acts as the carry-
select for the carry-out1 output. LEs in arithmetic mode can drive out registered
and unregistered versions of the LUT output.
The dynamic arithmetic mode also offers clock enable, counter enable, synchronous
up/down control, synchronous clear, synchronous load, and dynamic
adder/subtractor options. The LAB local interconnect data inputs generate the
counter enable and synchronous up/down control signals. The synchronous clear
and synchronous load options are LAB-wide signals that affect all registers in the
LAB. The Quartus II software automatically places any registers that are not used by
the counter into other LABs. The addnsub LAB-wide signal controls whether the LE
acts as an adder or subtractor.
Carry-Select Chain
The carry-select chain provides a very fast carry-select function between LEs in
dynamic arithmetic mode. The carry-select chain uses the redundant carry calculation
to increase the speed of carry functions. The LE is configured to calculate outputs for a
possible carry-in of 0 and carry-in of 1 in parallel. The carry-in0 and carry-in1
signals from a lower-order bit feed forward into the higher-order bit via the parallel
carry chain and feed into both the LUT and the next portion of the carry chain. Carry-
select chains can begin in any LE within an LAB.
Carry-Out0
LUT
LUT
LUT
LUT
Carry-Out1
Register chain
connection
clock (LAB Wide)
(LAB Wide)
ena (LAB Wide)
aclr (LAB Wide)
sload
(LAB Wide)
sclear
Register Feedback
(LAB Wide)
ADATA
ENA
D
ALD/PRE
aload
CLRN
Q
© October 2008 Altera Corporation
Chapter 2: MAX II Architecture
Row, column, and
direct link routing
Row, column, and
direct link routing
Local routing
LUT chain
connection
Register
chain output
Logic Elements