EP1S40F1020C6 Altera, EP1S40F1020C6 Datasheet - Page 160

• Manufacturer Part Number: EP1S40F1020C6
• Description: IC STRATIX FPGA 40K LE 1020-FBGA
• Manufacturer: Altera
• Series: Stratix®r

Specifications of EP1S40F1020C6

• Number Of Logic Elements/cells: 41250
• Number Of Labs/clbs: 4125
• Total Ram Bits: 3423744
• Number Of I /o: 773
• Voltage - Supply: 1.425 V ~ 1.575 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 1020-FBGA
• Family Name: Stratix
• Number Of Logic Blocks/elements: 41250
• # I/os (max): 773
• Frequency (max): 450.05MHz
• Process Technology: 0.13um (CMOS)
• Operating Supply Voltage (typ): 1.5V
• Logic Cells: 41250
• Ram Bits: 3423744
• Operating Supply Voltage (min): 1.425V
• Operating Supply Voltage (max): 1.575V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 1020
• Package Type: FC-FBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 544-1425; EP1S40SF1020C6

Configuration
3–6
Stratix Device Handbook, Volume 1
configuration, the device resets registers, enables I/O pins, and begins to
operate as a logic device. The I/O pins are tri-stated during power-up,
and before and during configuration. Together, the configuration and
initialization processes are called command mode. Normal device
operation is called user mode.
SRAM configuration elements allow Stratix devices to be reconfigured in-
circuit by loading new configuration data into the device. With real-time
reconfiguration, the device is forced into command mode with a device
pin. The configuration process loads different configuration data,
reinitializes the device, and resumes user-mode operation. You can
perform in-field upgrades by distributing new configuration files either
within the system or remotely.
PORSEL is a dedicated input pin used to select POR delay times of 2 ms
or 100 ms during power-up. When the PORSEL pin is connected to
ground, the POR time is 100 ms; when the PORSEL pin is connected to
V
The nIO_PULLUP pin enables a built-in weak pull-up resistor to pull all
user I/O pins to V
nIO_PULLUP is connected to V
ups on all user I/O pins are disabled. If connected to ground, the pull-ups
are enabled during configuration. The nIO_PULLUP pin can be pulled to
1.5, 1.8, 2.5, or 3.3 V for a logic level high.
VCCSEL is a dedicated input that is used to choose whether all dedicated
configuration and JTAG input pins can accept 1.5 V/1.8 V or 2.5 V/3.3 V
during configuration. A logic low sets 3.3 V/2.5 V, and a logic high sets
1.8 V/1.5 V. VCCSEL affects the following pins: TDI, TMS, TCK, TRST,
MSEL0, MSEL1, MSEL2, nCONFIG, nCE, DCLK, PLL_ENA, CONF_DONE,
nSTATUS. The VCCSEL pin can be pulled to 1.5, 1.8, 2.5, or 3.3 V for a logic
level high.
The VCCSEL signal does not control the dual-purpose configuration pins
such as the DATA[7..0] and PPA pins (nWS, nRS, CS, nCS, and
RDYnBSY). During configuration, these dual-purpose pins will drive out
voltage levels corresponding to the V
I/O bank containing the pin. After configuration, the dual-purpose pins
use I/O standards specified in the user design.
TDO and nCEO drive out at the same voltages as the V
powers the I/O bank containing the pin. Users must select the V
supply for bank containing TDO accordingly. For example, when using
the ByteBlaster
be powered up at 3.3 V.
CC
, the POR time is 2 ms.
™
MV cable, the V
CCIO
before and during device configuration. If
CC
CCIO
during configuration, the weak pull-
CCIO
for the bank containing TDO must
supply voltage that powers the
CCIO
Altera Corporation
supply that
July 2005
CCIO