PIC32MX795F512LT-80V/BG Microchip Technology, PIC32MX795F512LT-80V/BG Datasheet - Page 44

• Manufacturer Part Number: PIC32MX795F512LT-80V/BG
• Description: 512 KB Flash, 128 KB RAM, USB-OTG, Dual CAN, Ethernet, 80 MHz, 10-Bit ADC, DMA 1
• Manufacturer: Microchip Technology
• Series: PIC® 32MXr

Specifications of PIC32MX795F512LT-80V/BG

• Processor Series: PIC32MX7xx
• Core: MIPS
• Data Bus Width: 32 bit
• Program Memory Type: Flash
• Program Memory Size: 512 KB
• Data Ram Size: 128 KB
• Interface Type: USB, I2C, UART, RS-232, RS-485, SPI
• Maximum Clock Frequency: 80 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 5
• Operating Supply Voltage: 2.3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: XBGA-100
• Operating Temperature Range: - 40 C to + 85 C
• Supply Current (max): 10 mA
• Core Processor: MIPS32® M4K™
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: CAN, Ethernet, I²C, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: -
• Eeprom Size: -
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Lead Free Status / Rohs Status: Details

PIC32MX5XX/6XX/7XX
FIGURE 2-1:
2.2.1
The use of a bulk capacitor is recommended to improve
power supply stability. Typical values range from 4.7 µF
to 47 µF. This capacitor should be located as close to
the device as possible.
2.3
2.3.1
A low-ESR (1 ohm) capacitor is required on the
V
voltage regulator output. The V
be connected to V
tor, with at least a 6V rating, connected to ground. The
type can be ceramic or tantalum. Refer to
“Electrical Characteristics”
on C
DS61156G-page 44
CAP
0.1 µF
Ceramic
C
V
BP
DD
EFC
R
/V
C
CORE
R1
Capacitor on Internal Voltage
Regulator (V
specifications.
BULK CAPACITORS
INTERNAL REGULATOR MODE
10 Ω
pin, which is used to stabilize the internal
MCLR
V
V
SS
DD
DD
, and must have a C
RECOMMENDED
MINIMUM CONNECTION
C
CAP
EFC
PIC32
0.1 µF
Ceramic
C
BP
for additional information
/V
CAP
CORE
/V
CORE
)
V
V
DD
Section 31.0
SS
0.1 µF
Ceramic
C
0.1 µF
Ceramic
C
pin must not
BP
EFC
BP
0.1 µF
Ceramic
C
BP
capaci-
2.4
The
functions:
• Device Reset
• Device Programming and Debugging
Pulling The MCLR pin low generates a device Reset.
Figure 2-2
device programming and debugging, the resistance
and capacitance that can be added to the pin must
be considered. Device programmers and debuggers
drive the MCLR pin. Consequently, specific voltage
levels (V
not be adversely affected. Therefore, specific values
of R and C will need to be adjusted based on the
application and PCB requirements.
For example, as illustrated in
recommended that the capacitor C, be isolated from
the MCLR pin during programming and debugging
operations.
Place the components illustrated in
one-quarter inch (6 mm) from the MCLR pin.
FIGURE 2-2:
Note 1: R ≤ 10 kΩ is recommended. A suggested start-
MCLR
2: R1 ≤ 470Ω will limit any current flowing into
3: The capacitor can be sized to prevent uninten-
Master Clear (MCLR) Pin
IH
illustrates a typical MCLR circuit. During
ing value is 10 kΩ. Ensure that the MCLR pin
V
MCLR from the external capacitor C, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
V
tional Resets from brief glitches or to extend
the device Reset period during the POR.
and V
V
IH
IH
DD
R
and V
and V
pin
JP
C
IL
© 2009-2011 Microchip Technology Inc.
) and fast signal transitions must
IL
IL
provides
specifications are met.
specifications are met.
EXAMPLE OF MCLR PIN
CONNECTIONS
R1
MCLR
two
PIC32
Figure
Figure 2-2
specific
2-2, it is
device
within