DS1876T+T&R Maxim Integrated Products, DS1876T+T&R Datasheet - Page 14

• Manufacturer Part Number: DS1876T+T&R
• Description: IC CTRLR SFP DUAL LDD 28TQFN
• Manufacturer: Maxim Integrated Products
• Type: SFP Laser Controllerr

Specifications of DS1876T+T&R

• Input Type: Logic
• Output Type: Logic
• Interface: I²C
• Current - Supply: 10mA
• Mounting Type: Surface Mount
• Package / Case: 28-TQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SFP Controller with Dual LDD Interface
Figure 3. Quick-Trip Sample Timing
Table 2. ADC Default Monitor Full-Scale Ranges
corresponding alarms and warnings (TXP HI1, TXP LO1,
TXP HI2, TXP LO2, BIAS HI1, and BIAS HI2) are asserted
or deasserted.
After resetting, the device completes one QT cycle
before making comparisons. The TXP LO quick-trip
alarm updates its alarm bit, but does not create FETG
until after TXD
figured to wait for TXD
using QTHEXT_ (Table 02h, Register 88h).
Monitoring functions on the DS1876 include six quick-
trip comparators and six ADC channels. This monitoring
combined with the alarm enables (Table 01h/05h) deter-
mines when/if the DS1876 turns off DACs and triggers
the TXFOUT and TXDOUT1, TXDOUT2 outputs. All the
monitoring levels and interrupt masks are user program-
mable.
Six quick-trip monitors are provided to detect potential
laser safety issues and LOS status. These monitor the
following:
1) High Bias Current 1 (HBATH1), causing QT BIAS1 HI
2) Low Transmit Power 1 (LTXP1), causing QT TXP1 LO
3) High Transmit Power 1 (HTXP1), causing QT TXP1 HI
4) High Bias Current 2 (HBATH2), causing QT BIAS2 HI
5) Low Transmit Power 2 (LTXP2), causing QT TXP2 LO
6) High Transmit Power 2 (HTXP2), causing QT TXP2 HI
14
Temperature (NC)
V
PMON1, PMON2 and BMON1, BMON2 (V)
CC
(V)
_____________________________________________________________________________________
SIGNAL (UNITS)
EXT
QUICK-TRIP SAMPLE TIMES
. TXP HI and BIAS HI can also be con-
Six Quick-Trip Monitors and Alarms
Monitors and Fault Detection
EXT
; however, this can be disabled
SAMPLE
LTXP2
+FS SIGNAL
127.996
SAMPLE
HBIAS1
6.5528
2.4997
Monitors
t
REP
SAMPLE
HBIAS2
The high and low transmit power quick-trip registers
(HTXP1, HTXP2, LTXP1, and LTXP2) set the thresholds
used to compare against the PMON1 and PMON2 volt-
ages to determine if the transmit power is within speci-
fication. The HBATH1 and HBATH2 QTs compare the
BMON1 and BMON2 inputs (generally from the laser
driver’s bias monitor output) against their threshold set-
tings to determine if the present bias current is above
specification. The bias and power QTs are routed to
FETG through interrupt masks to allow combinations
of these alarms to be used to trigger FETG. The bias
and power QTs are directly connected to TXFOUT (see
Figure 9). The user can program up to eight different
temperature-indexed threshold levels for HBATH1 and
HBATH2 (Table 06h, Registers E0h-E7h).
The ADC monitors six channels that measure tem-
perature (internal temp sensor), V
BMON1, and BMON2 using an analog multiplexer to
measure them round-robin with a single ADC (see the
ADC Timing section). The channels have a customer-
programmable full-scale range, and all channels have a
customer-programmable offset value that is factory pro-
grammed to a default value (see Table 2). Additionally,
PMON1, PMON2 and BMON1, BMON2 can right-shift
results by up to 7 bits before the results are compared
to alarm thresholds or read over the I
customers with specified ADC ranges to calibrate the
ADC full scale to a factor of 1/2
to measure small signals. The DS1876 can then right-
shift the results by n bits to maintain the bit weight of their
specification.
SAMPLE
HTXP1
+FS HEX
QT CYCLE
7FFF
FFF8
FFF8
SAMPLE
HTXP2
SAMPLE
LTXP1
-FS SIGNAL
Six ADC Monitors and Alarms
SAMPLE
-128
LTXP2
0
0
n
SAMPLE
of their specified range
HBIAS1
CC
2
, PMON1, PMON2,
C bus. This allows
-FS HEX
8000
0000
0000