LM41CIMTX/NOPB National Semiconductor, LM41CIMTX/NOPB Datasheet
LM41CIMTX/NOPB
Specifications of LM41CIMTX/NOPB
Related parts for LM41CIMTX/NOPB
LM41CIMTX/NOPB Summary of contents
Page 1
... General Description The LM41 is a hardware monitor that measures 2 tempera- ture zones, 5 voltages and has a single-wire interface com- patible with National Semiconductor’s SensorPath bus. Sen- sorPath data is pulse width encoded, thereby allowing the LM41 to be easily connected to many general purpose micro-controllers ...
Page 2
Connection Diagram TSSOP-14 Top View National Package Number MTC14C Pin Description Pin Number Pin Name 1, 10, 13 GND 3 V+/+3.3V_SBY 4 SWD 5 ADD 6 +1.2V 7 +2. +5V 12 +12V ...
Page 3
Block Diagram 3 20070303 www.national.com ...
Page 4
Absolute Maximum Ratings (Notes Supply Voltage (V ) Voltage at Any Digital Input or Output Pin Voltage on 12V Analog Input Voltage on 5V Analog Input Voltage on D+ −0 (V+ + 0.05 V) Voltage ...
Page 5
TEMPERATURE-TO-DIGITAL CONVERTER CHARACTERISTICS Parameter Diode Source Current Diode Source Current High Current to Low Current Ratio ANALOG TO DIGITAL CONVERTER CHARACTERISTICS Symbol Parameter TUE Total Unadjusted Error(Note 11) Resolution DNL Differential Non-linearity Power Supply Sensitivity Input Resistance, all analog inputs ...
Page 6
AC Electrical Characteristics The following specification apply for =0˚ =85˚C; all other limits MIN MAX specification revision 0.98. Please refer to that speciation for further details. ...
Page 7
PIN Pin Pin # Name Circuit GND SWD A 5 ADD A 6 +1. +2. +5V ...
Page 8
Timing Diagrams FIGURE 1. Timing for Data Bits 0, 1 and Start Bit. See Section 1.2 "SensorPath BIT SIGNALING" for further details. www.national.com 8 20070304 ...
Page 9
Timing Diagrams (Continued) FIGURE 2. Timing for Attention Request and Reset. See Section 1.2 "SensorPath BIT SIGNALING" for further details. 9 20070305 www.national.com ...
Page 10
... The digitized data can be retrieved over a simple single-wire interface called SensorPath. Sensor- Path has been defined by National Semiconductor and is optimized for hardware monitoring. National offers a royalty- free license in connection with its intellectual property rights in the SensorPath bus ...
Page 11
Functional Description Signal labels that begin with the label Slv_ depict the drive by the LM41. All other signals show what would be seen when probing SWD for a particular function (e.g. "Master Wr 0" is the Master transmitting ...
Page 12
Functional Description 1.3.2 Read Transaction During a read transaction, the master reads data from a register at a specified address within a slave. A read trans- action begins with a Start Bit and ends with an ACK bit, as ...
Page 13
Functional Description • Data Bits This is the data written to the LM41 register, are driven by the master. Data is transferred serially with the most significant bit first. The number of data bits may vary from one address ...
Page 14
Functional Description All devices (master or slave) must monitor the bus for an Attention Request signal. The following notes clarify the intended system operation that uses the Attention Request Indication. • Masters are expected to use the attention request ...
Page 15
Register Set 2.1 REGISTER SET SUMMARY P Bit Reg Register Add Name W R MSb Val 000 000 Device R * 00h Number 000 001 Manufacturer R 100Bh 0 01h ID 000 010 Device ID R ...
Page 16
... Register R/ O Add Name W R MSb Val Manufacturer 000 001 R 100Bh ID The manufacturer ID matches that assigned to National Semiconductor by the PCI SIG. This register may be used to identify the manufacturer of the device in order to perform manufacturer specific operations. www.national.com Bit 7 Bit 6 Bit Val Reserved ...
Page 17
Register Set (Continued) 2.5 DEVICE ID (Addr: 000 010; 02h) P Bit Reg Register Add Name W R MSb Val 000 010 Device ID R 24h 0 The device ID is defined by the manufacturer of ...
Page 18
Register Set (Continued) Bit Type 7 RO BER (Bus Error) This bit is set when the device either generates, or receives an error indication in the ACK bit of the transaction (i.e., no-acknowledge). BER is cleared by Device Reset ...
Page 19
Register Set (Continued) The minimum scan rate is recommended to be 4Hz (i.e. the measurement data is updated at least once in 250 ms), see Section 2.11 for further details. In Low-Power Mode, the scan rate is four times ...
Page 20
Register Set (Continued) 2.9.3 Temperature Data Readout (Addr: 001 001; 09h) P Reg Register R/ O Add Name W R MSb Val Local Temperature Data Readout MSb 001 001 R Processor/ Sign Remote Temperature Data Readout Bit Type 0 ...
Page 21
Register Set (Continued) Temperature -255.5 ˚C -256 ˚C 2.9.4 Temperature Control (Addr: 001 010; 0Ah) This register is set to the reset value by a Device Reset. P Bit Reg Register Add Name W R MSb ...
Page 22
Register Set (Continued) Function Event The Voltage-Only Measurement function generates a Function Event to the master whenever a conversion cycle is completed and new data is stored in the Readout register. When the new data is stored into the ...
Page 23
Register Set (Continued) Input Voltage for Nominal Sensor Reading Number (code 384 or (SNUM) Voltage Input 180h) 0 +2.5V 2.5V 1 +1.2V 1.2V 2 +3.3V_SBY 3.3V (V +12V 12V 2.10.4 Voltage Control (Addr: 010 010; ...
Page 24
Register Set (Continued) Bit Type 1-0 RO CR0 and CR1 (Conversion Rate bits 0 and 1) These bits control the conversion rate of the LM41 for more details see Table Conversion Rate Control and desciption below. 7-2 RO Reserved. ...
Page 25
Application Hints (Continued) 3.1 DIODE NON-IDEALITY 3.1.1 Diode Non-Ideality Factor Effect on Accuracy When a transistor is connected as a diode, the following relationship holds for variables and I BE where: −19 • 1.6x10 ...
Page 26
Application Hints 3. Ideally, the LM41 should be placed within 10cm of the Processor diode pins with the traces being as straight, short and identical as possible. Trace resistance of 0.7Ω can cause as much as 1˚C of error. ...
Page 27
... BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. ...