LM41CIMTX/NOPB National Semiconductor, LM41CIMTX/NOPB Datasheet - Page 25

• Manufacturer Part Number: LM41CIMTX/NOPB
• Description: IC HARDWARE MONITOR 14-TSSOP
• Manufacturer: National Semiconductor

Specifications of LM41CIMTX/NOPB

• Applications: Monitors
• Interface: 1-Wire
• Voltage - Supply: 3 V ~ 3.6 V
• Package / Case: 14-TSSOP
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LM41CIMTX

3.0 Application Hints
3.1 DIODE NON-IDEALITY
3.1.1 Diode Non-Ideality Factor Effect on Accuracy
When a transistor is connected as a diode, the following
relationship holds for variables V
where:
In the active region, the -1 term is negligible and may be
eliminated, yielding the following equation
In the above equation, η and I
process that was used in the fabrication of the particular
diode. By forcing two currents with a very controlled ration
(N) and measuring the resulting voltage difference, it is
possible to eliminate the I
voltage difference yields the relationship:
The non-ideality factor, η, is the only other parameter not
accounted for and depends on the diode that is used for
measurement. Since ∆V
the variations in η cannot be distinguished from variations in
temperature. Since the non-ideality factor is not controlled by
the temperature sensor, it will directly add to the inaccuracy
of the sensor. For the Pentium III Intel specifies a
variation in η from part to part. As an example, assume a
temperature sensor has an accuracy specification of
room temperature of 25 ˚C and the process used to manu-
facture the diode has a non-ideality variation of
resulting accuracy of the temperature sensor at room tem-
perature will be:
The additional inaccuracy in the temperature measurement
caused by η, can be eliminated if each temperature sensor is
calibrated with the remote diode that it will be paired with.
The following table shows the variations in non-ideality for a
variety of processors.
• q = 1.6x10
• T = Absolute Temperature in Kelvin
• k = 1.38x10
• η is the non-ideality factor of the process the diode is
• I
• I
• V
manufactured on,
S
f
= Forward Current through the base emitter junction
BE
= Saturation Current and is process dependent,
= Base Emitter Voltage drop
T
ACC
−19
=
−23
±
Coulombs (the electron charge),
joules/K (Boltzmann’s constant),
3˚C + (
BE
±
S
is proportional to both η and T,
1% of 298 ˚K) =
term. Solving for the forward
S
BE
are dependant upon the
, T and I
(Continued)
f
:
±
6 ˚C
±
1%. The
±
3˚C at
±
1%
25
3.2 PCB LAYOUT for MINIMIZING NOISE
In a noisy environment, such as a processor mother board,
layout considerations are very critical. Noise induced on
traces running between the remote temperature diode sen-
sor and the LM41 can cause temperature conversion errors.
Keep in mind that the signal level the LM41 is trying to
measure is in microvolts. The following guidelines should be
followed:
1. Place the 100 pF and 0.1 µF power supply bypass
2. The recommended 100 pF diode capacitor actually has
Processor Family
Pentium II
Pentium III CPUID 67h
Pentium III CPUID
68h/PGA370Socket/Celeron
Pentium 4, 423 pin
Pentium 4, 478 pin
Pentium 4 on 0.13
micron process,
2-3.06GHz
Pentium 4 on 90 nm
process
Pentium M Processor
(Centrino)
MMBT3904
AMD Athlon MP model
6
capacitors as close as possible to the LM41’s power pin.
Place the recommended thermal diode 100 pF capacitor
as close as possible to the LM41’s D+ and D− pins.
Make sure the traces to the thermal diode 100 pF ca-
pacitor are matched.
a range of 0 pF to 3.3 nF (see curve in Typical Perfor-
mance Characteristics for effect on accuracy). The av-
erage temperature accuracy will not degrade. Increasing
the capacitance will lower the corner frequency where
differential noise error affects the temperature reading
thus producing a reading that is more stable. Con-
versely, lowering the capacitance will increase the cor-
ner frequency where differential noise error affects the
temperature reading thus producing a reading that is
less stable.
FIGURE 8. Ideal Diode Trace Layout
1.00151 1.00220 1.00289 3.06 Ω
1.0057 1.008 1.0125
0.9933 1.0045 1.0368
0.9933 1.0045 1.0368
1.0011 1.0021 1.0030 3.64 Ω
1.002
min
1
1
η, non-ideality
1.0065 1.0173
1.0065 1.0125
1.003
1.008
1.011
typ
1.016
max
www.national.com
3.33 Ω
Series
20070317
R