AM29DL164DT-120WCI Spansion Inc., AM29DL164DT-120WCI Datasheet - Page 50

• Manufacturer Part Number: AM29DL164DT-120WCI
• Manufacturer: Spansion Inc.

Specifications of AM29DL164DT-120WCI

• Cell Type: NOR
• Density: 16Mb
• Access Time (max): 120ns
• Interface Type: Parallel
• Boot Type: Top
• Address Bus: 21/20Bit
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Package Type: FBGA
• Program/erase Volt (typ): 8.5 to 9.5V
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8/16Bit
• Number Of Words: 2M/1M
• Supply Current: 16mA
• Mounting: Surface Mount
• Pin Count: 48
• Lead Free Status / Rohs Status: Not Compliant

ERASE AND PROGRAMMING PERFORMANCE
Notes:
1. Typical program and erase times assume the following conditions: 25°C, 3.0 V V
2. Under worst case conditions of 90°C, V
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table
6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles.
LATCHUP CHARACTERISTICS
Note: Includes all pins except V
PACKAGE AND PIN CAPACITANCE
Notes:
1. Sampled, not 100% tested.
2. Test conditions T
DATA RETENTION
50
Parameter
Sector Erase Time
Chip Erase Time
Byte Program Time
Word Program Time
Accelerated Byte/Word Program Time
Chip Program Time
(Note 3)
Input voltage with respect to V
(including A9, OE#, and RESET#)
Input voltage with respect to V
V
Parameter Description
Minimum Pattern Data Retention Time
CC
Parameter Symbol
programming typicals assume checkerboard pattern.
program faster than the maximum program times listed.
14 for further information on command definitions.
Current
C
C
C
OUT
IN2
IN
A
= 25°C, f = 1.0 MHz.
Description
Control Pin Capacitance
Parameter Description
SS
SS
Output Capacitance
CC
Word Mode
Byte Mode
Input Capacitance
on all pins except I/O pins
on all I/O pins
. Test conditions: V
CC
= 2.7 V, 1,000,000 cycles.
D A T A
Typ (Note 1)
CC
Am29DL16xD
= 3.0 V, one pin at a time.
0.7
27
5
7
4
9
6
V
V
V
OUT
S H E E T
IN
IN
= 0
= 0
= 0
Max (Note 2)
Test Setup
150
210
120
15
27
18
Test Conditions
TSOP/SO
TSOP/SO
TSOP/SO
–100 mA
–1.0 V
–1.0 V
BGA
BGA
BGA
Min
CC
150°C
125°C
, 1,000,000 cycles. Additionally,
Unit
sec
sec
sec
µs
µs
µs
Typ
4.2
8.5
5.4
7.5
3.9
6
Excludes 00h programming
prior to erasure (Note 4)
21533E6 February 26, 2009
Excludes system level
overhead (Note 5)
Comments
V
Max
7.5
6.5
4.7
12
+100 mA
CC
5
9
12.5 V
Min
Max
10
20
+ 1.0 V
Unit
Years
Years
pF
pF
pF
pF
pF
pF
Unit