SC16IS760IBS,128 NXP Semiconductors, SC16IS760IBS,128 Datasheet - Page 29

• Manufacturer Part Number: SC16IS760IBS,128
• Description: IC UART I2C/SPI 24-HVQFN
• Manufacturer: NXP Semiconductors

Specifications of SC16IS760IBS,128

• Features: Low Current
• Number Of Channels: 1, UART
• Fifo's: 64 Byte
• Protocol: RS232, RS485
• Voltage - Supply: 2.5V, 3.3V, 5V
• With Auto Flow Control: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Package / Case: 24-VQFN Exposed Pad, 24-HVQFN, 24-SQFN, 24-DHVQFN
• For Use With: 568-4000 - DEMO BOARD SPI/I2C TO DUAL UART568-3510 - DEMO BOARD SPI/I2C TO UART
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935279279128; SC16IS760IBS-F; SC16IS760IBS-F

NXP Semiconductors
SC16IS740_750_760_6
Product data sheet
8.8 Interrupt Enable Register (IER)
The Interrupt Enable Register (IER) enables each of the six types of interrupt, receiver
error, RHR interrupt, THR interrupt, modem status, Xoff received, or CTS/RTS change of
state from LOW to HIGH. The IRQ output signal is activated in response to interrupt
generation.
Table 19.
[1]
[2]
Bit
7
6
5
4
3
2
1
0
IER[7:4] can only be modified if EFR[4] is set, that is, EFR[4] is a write enable. Re-enabling IER[1] will not
cause a new interrupt if the THR is below the threshold.
Only available on the SC16IS750/SC16IS760.
Symbol
IER[7]
IER[6]
IER[5]
IER[4]
IER[3]
IER[2]
IER[1]
IER[0]
Interrupt Enable Register bits description
Table 19
[1]
[1]
[1]
[1]
Description
CTS interrupt enable
RTS interrupt enable
Xoff interrupt
Sleep mode
Modem Status Interrupt
Remark: See IOControl register bit 1 in
program the pins as modem pins.
Receive Line Status interrupt
Transmit Holding Register interrupt.
Receive Holding Register interrupt.
logic 0 = disable the CTS interrupt (normal default condition)
logic 1 = enable the CTS interrupt
logic 0 = disable the RTS interrupt (normal default condition)
logic 1 = enable the RTS interrupt
logic 0 = disable the Xoff interrupt (normal default condition)
logic 1 = enable the Xoff interrupt
logic 0 = disable Sleep mode (normal default condition)
logic 1 = enable Sleep mode. See
logic 0 = disable the modem status register interrupt (normal default
condition)
logic 1 = enable the modem status register interrupt
logic 0 = disable the receiver line status interrupt (normal default condition)
logic 1 = enable the receiver line status interrupt
logic 0 = disable the THR interrupt (normal default condition)
logic 1 = enable the THR interrupt
logic 0 = disable the RHR interrupt (normal default condition)
logic 1 = enable the RHR interrupt
shows the Interrupt Enable Register bit settings.
Single UART with I
Rev. 06 — 13 May 2008
[2]
.
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
SC16IS740/750/760
Section 7.6 “Sleep mode”
Table 30
for the description of how to
© NXP B.V. 2008. All rights reserved.
for details.
29 of 62