LM4781TA/NOPB National Semiconductor, LM4781TA/NOPB Datasheet - Page 8

• Manufacturer Part Number: LM4781TA/NOPB
• Description: IC AMP AUDIO PWR 35W AB TO220-27
• Manufacturer: National Semiconductor
• Series: Overture™r
• Type: Class ABr

Specifications of LM4781TA/NOPB

• Output Type: 3-Channel
• Max Output Power X Channels @ Load: 35W x 3 @ 8 Ohm
• Voltage - Supply: 20 V ~ 70 V, ±10 V ~ 35 V
• Features: Depop, Mute, Short-Circuit and Thermal Protection
• Mounting Type: Through Hole
• Package / Case: TO-220-27 (Bent and Staggered Leads)
• For Use With: LM4781TABD - BOARD EVALUATION LM4781TA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: *LM4781TA; *LM4781TA/NOPB; LM4781TA

www.national.com
10
12
13
14
15
16
17
18
19
20
21
22
23
24
11
External Components Description
(Figures 1-5)
1
2
3
4
5
6
7
8
9
Note 16: Optional components dependent upon specific design requirements.
Components
R
R
R
R
(Note 16)
C
(Note 16)
C
(Note 16)
C
(Note 16)
C
R
(Note 16)
R
(Note 16)
C
(Note 16)
R
(Note 16)
C
(Note 16)
L (Note 16)
R (Note 16)
R
C
R
(Note 16)
R
R
R
C
S
R
1
B
i
f
f2
f
C
i
S
V
IN
IN
SN
SN
A
A
INP
BI
E
M
M
OUT
Prevents current from entering the amplifier’s non-inverting input. This current may pass through to the load
during system power down, because of the amplifier’s low input impedance when the undervoltage circuitry
is off. This phenomenon occurs when the V
Inverting input resistance. Along with R
Feedback resistance. Along with R
Feedback resistance. Works with Cf and Rf creating a lowpass filter that lowers AC gain at high
frequencies. The -3dB point of the pole occurs when: (R
Non-Inverting configuration shown in Figure 5.
Compensation capacitor. Works with R
Compensation capacitor. Reduces the gain at higher frequencies to avoid quasi-saturation oscillations of the
output transistor. Also suppresses external electromagnetic switching noise created from fluorescent lamps.
Feedback capacitor which ensures unity gain at DC. Along with R
1/(2πR
Provides power supply filtering and bypassing. Refer to the Supply Bypassing application section for proper
placement and selection of bypass capacitors.
Acts as a volume control by setting the input voltage level.
Sets the amplifier’s input terminals DC bias point when C
create a highpass filter at f
the outputs when the inputs are floating. Recommended values are 10kΩ to 47kΩ. Refer to Figure 5.
Input capacitor. Prevents the input signal’s DC offsets from being passed onto the amplifier’s inputs.
Works with C
Works with R
pole is set at f
Provides high impedance at high frequencies so that R may decouple a highly capacitive load and reduce
the Q of the series resonant circuit. Also provides a low impedance at low frequencies to short out R and
pass audio signals to the load. Refer to Figure 5.
Provides DC voltage biasing for the transistor Q1 in single supply operation.
Provides bias filtering for single supply operation.
Limits the voltage difference between the amplifier’s inputs for single supply operation. Refer to the Clicks
and Pops application section for a more detailed explanation of the function of R
Provides input bias current for single supply operation. Refer to the Clicks and Pops application section for
a more detailed explanation of the function of R
Establishes a fixed DC current for the transistor Q1 in single supply operation. This resistor stabilizes the
half-supply point along with C
Mute resistance set up to allow 0.5mA to be drawn from each MUTE pin to turn the muting function off.
→ R
Current curves in the Typical Performance Characteristics section.
Mute capacitance set up to create a large time constant for turn-on and turn-off muting.
Mute switch. When open or switched to GND, the amplifier will be in mute mode.
Reduces current flow between outputs that are caused by Gain or DC offset differences between the
amplifiers.
M
i
is calculated using: R
C
i
).
SN
SN
C
= 1/(2πR
to stabilize the output stage by creating a pole that reduces high frequency instabilities.
to stabilize the output stage by creating a pole that reduces high frequency instabilities. The
SN
C
C
M
= 1/(2πR
SN
A
≤ (|V
.
). Refer to Figure 5.
i
, sets AC gain.
EE
| − 2.6V)/l where l ≥ 0.5mA. Refer to the Mute Attenuation vs Mute
IN
f
f
, sets AC gain.
C
and R
IN
Functional Description
8
). If the value of R
+
and V
f2
BI
to reduce AC gain at higher frequencies.
.
-
supply voltages are below 1.5V.
f
- R
IN
is present in the circuit. Also works with C
i
)/2 = R
IN
is too large, oscillations may be observed on
i
also creates a highpass filter at f
f
// [1/(2πf
c
C
f
) + R
INP
.
f2
] for the
c
=
IN
to