X24C00 Intersil Corporation, X24C00 Datasheet
X24C00
Available stocks
Related parts for X24C00
X24C00 Summary of contents
Page 1
... X24C00 2 Serial E PROM DESCRIPTION The X24C00 is a CMOS 128 bit serial E nally organized The X24C00 features a serial interface and software protocol allowing operation on a simple two wire bus. 2 Xicor E PROMs are designed and tested for applica- tions requiring extended endurance. Inherent data re- tention is greater than 100 years. The X24C00 is fabricated with Xicor’ ...
Page 2
... The master will always initiate data transfers and provide the clock for both transmit and receive operations. There- fore, the X24C00 will be considered a slave in all applications. Clock and Data Conventions Data states on the SDA line can change only during SCL LOW ...
Page 3
... X24C00 Figure 1. Data Validity SCL SDA Figure 2. Definition of Start and Stop Conditions SCL SDA START CONDITION Figure 3. Control Byte DATA STABLE DATA CHANGE START 3 3836 FHD F03 STOP CONDITION 3836 FHD F04 3836 FHD F05 ...
Page 4
... During the second don’t care clock cycle, starts and stops are ignored. The master must free the bus prior to the end of this clock cycle to allow the X24C00 to begin outputting data (Figures 5 and 6 ...
Page 5
... X24C00 ABSOLUTE MAXIMUM RATINGS* Temperature under Bias X24C00 ...................................... – +135 C Storage Temperature ....................... – +150 C Voltage on any Pin with Respect ............................................ D.C. Output Current ............................................. 5mA Lead Temperature (Soldering, 10 seconds) .............................. 300 C RECOMMENDED OPERATING CONDITIONS Temperature Min. Commercial 0 C Industrial –40 C Military – ...
Page 6
... X24C00 POWER-UP TIMING Symbol PUR (3) t Power-up to Read Operation t PUW (3) Power-up to Write Operation EQUIVALENT A.C. LOAD CIRCUIT 5V 2.16K OUTPUT 3.07K A.C. CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.) Read & Write Cycle Limits Symbol f SCL Clock Frequency SCL t SCL LOW to SDA Data Out Valid ...
Page 7
... Note: (4) The write cycle time is the time from the initiation of a write sequence to the end of the internal erase/program cycle. During the write cycle, the X24C00 bus interface circuits are disabled, SDA is high impedance, and the device does not respond to start conditions. ...
Page 8
... X24C00 PACKAGING INFORMATION 8-LEAD MINIATURE SMALL OUTLINE GULL WING PACKAGE TYPE M 0.012 + 0.006 / -0.002 0.040 (1.02 0.007 (0.18) 0.005 (0.13) NOTE: 1. ALL DIMENSIONS IN INCHES AND (MILLIMETERS) 0.118 0.002 (3.00 0.05) (0.30 + 0.15 / -0.05) 0.118 0.002 (3.00 0.05) 0.030 (0.76) 0.0216 (0.55) 7 TYP 0.036 (0.91) 0.032 (0.81) 0.002 0.008 (0.20) 0.05) 0.004 (0.10) 0.150 (3.81) REF. 0.193 (4.90) REF. 8 0.0256 (0.65) TYP R 0 ...
Page 9
... X24C00 PACKAGING INFORMATION HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.015 (0.38) MAX. TYP. 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH 8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P 0.430 (10.92) 0.360 (9.14) PIN 1 INDEX PIN 1 0.300 (7.62) REF. SEATING PLANE 0.150 (3.81) ...
Page 10
... X24C00 PACKAGING INFORMATION 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX 0.010 (0.25) 0.020 (0.50) 0 – 8 0.016 (0.410) 0.037 (0.937) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 0.150 (3.80) 0.158 (4.00) PIN 1 0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7 0.004 (0.19) 0.050 (1.27) 0.010 (0.25 0.0075 (0.19) 0.250" 0.010 (0.25) ...
Page 11
... Blank = Commercial = + Industrial = – + Military = – +125 C Package M = 8-Lead MSOP P = 8-Lead Plastic DIP S = 8-Lead SOIC Blank = 8-Lead SOIC X24C00 8-Lead Plastic DIP X Blank = 4.5V to 5.5V + 4.5V to 5.5V, – + 4.5V to 5.5V, – + 5.5V + 5.5V, – ...