TDA8595TH/N2C,118 NXP Semiconductors, TDA8595TH/N2C,118 Datasheet - Page 33

• Manufacturer Part Number: TDA8595TH/N2C,118
• Description: IC AMP AUDIO PWR 64W QUAD 36HSOP
• Manufacturer: NXP Semiconductors
• Type: Class ABr

Specifications of TDA8595TH/N2C,118

• Output Type: 4-Channel (Quad)
• Max Output Power X Channels @ Load: 64W x 4 @ 2 Ohm
• Voltage - Supply: 8 V ~ 18 V
• Features: Depop, I²C, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Surface Mount
• Package / Case: 36-HSOP
• Product: Class-AB
• Operational Class: Class-AB
• Audio Amplifier Output Configuration: 4-Channel Stereo
• Output Power (typ): 25x4@4OhmW
• Audio Amplifier Function: Speaker
• Total Harmonic Distortion: 0.14@4Ohm@12W%
• Single Supply Voltage (typ): 14.4V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Requirement: Single
• Power Dissipation: 80W
• Rail/rail I/o Type: No
• Single Supply Voltage (min): 8V
• Single Supply Voltage (max): 18V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 36
• Package Type: HSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 935284654118; TDA8595TH/N2C-T; TDA8595TH/N2C-T

NXP Semiconductors
Table 17.
Refer to test circuit (see
specified. Tested at T
[1]
[2]
[3]
[4]
[5]
12. Performance diagrams
TDA8595_2
Product data sheet
Symbol
Z
V
B
i
mute
o(mute)(RMS)
p
Operation above 16 V in a 2
after 16 ms resulting in an ‘audio hole’.
V
The times are specified without leakage current. For a leakage current of 10 A on the SVR pin, the delta time is specified. If the
capacitor value on the SVR pin changes with
ESR of 15
Standard I
the maximal LOW-level is defined by V
For optimum channel separation (
R
STB
ACGND
depends on the current into the STB pin: minimum = (1429
Characteristics
2
=
C-bus specification: maximum LOW-level = 0.3
for the capacitor on the SVR pin.
R
----- -
Parameter
input impedance
mute attenuation
RMS mute output voltage
power bandwidth
4
S
amb
should be in series with the ACGND capacitor.
Figure
= 25 C; guaranteed for T
Fig 18. Total harmonic distortion as a function of output power; 4
…continued
(1) f = 10 kHz.
(2) f = 1 kHz.
(3) f = 100 Hz.
30) at V
mode with reactive load can trigger the amplifier protection. The amplifier switches off and will restart
THD
(%)
10
10
10
10
V
10
cs
P
1
2
1
2
3
10
), supply voltage ripple rejection (SVRR) and common mode rejection ratio (CMRR), a resistor
= 14.4 V.
P
DD
2
= V
= 5 V and the minimum HIGH-level by V
P1
Conditions
T
T
V
V
filter 20 Hz to 22 kHz
30 %, the specified time will also change with
= V
1 dB
amb
amb
o
i
= 1 V (RMS);
Rev. 02 — 21 November 2007
/ V
P2
amb
= 40 C to +105 C
= 0 C to 105 C
o(mute)
= 14.4 V; R
= 40 C to +105 C.
10
; V
1
V
DD
i
= 50 mV
, minimum HIGH-level = 0.7
L
= 4 ; f = 1 kHz; R
I
STB
) + 5.4 V, maximum = (3143
I
2
1
C-bus controlled 4
DD
= 3.3 V.
S
= 0 ; normal mode; unless otherwise
Min
50
60
80
-
-
V
30 %. The specified times include an
DD
10
. To comply with 5 V and 3.3 V logic
(1)
(2)
(3)
Typ
70
70
92
25
20 to
20000
I
45 W power amplifier
STB
P
load
o
(W)
) + 5.6 V.
TDA8595
001aad139
© NXP B.V. 2007. All rights reserved.
Max
95
95
-
-
-
10
2
Unit
k
k
dB
Hz
33 of 50
V