N80C196KC Intel Corporation, N80C196KC Datasheet
N80C196KC
Available stocks
Related parts for N80C196KC
N80C196KC Summary of contents
Page 1
... Intel products except as provided in Intel’s Terms and Conditions of Sale for such products Intel retains the right to make changes to these specifications at any time without notice Microcomputer Products may have minor variations to this specification known as errata COPYRIGHT INTEL CORPORATION 1995 Dynamically Configurable 8-Bit or Y ...
Page 2
Figure 1 8XC196KC Block Diagram IOC3 (0CH HWIN1 READ WRITE) NOTE e RSV Reserved bits must be 0 Figure 2 8XC196KC New SFR Bit (CLKOUT Disable) 2 270942 – 1 270942 – 45 ...
Page 3
PROCESS INFORMATION This device is manufactured on PX29 5 or PX29 9 a CHMOS III process Additional process and reliabili- ty information is available in Intel’s Components Quality and Reliability Handbook Order Number 210997 EXAMPLE N87C196KC is 68-Lead PLCC OTPROM ...
Page 4
Figure 4 68-Lead PLCC Package 4 270942 – 2 ...
Page 5
Figure 5 S8XC196KC 80-Pin QFP Package 8XC196KC 8XC196KC20 270942 – ...
Page 6
Figure 6 80-Pin SQFP Package 270942 – 44 ...
Page 7
PIN DESCRIPTIONS Symbol V Main supply voltage (5V Digital circuit ground (0V) There are multiple Reference voltage for the A D converter (5V) V REF portion of the A D converter and the logic used ...
Page 8
PIN DESCRIPTIONS (Continued) Symbol Ports 3 and 4 8-bit bidirectional I O ports with open drain outputs These pins are shared with the multiplexed address data bus which has strong internal pullups HOLD Bus Hold input requesting control ...
Page 9
ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Ambient Temperature b Under Bias Storage Temperature Voltage On Any Pin Voltage from ANGND PP ...
Page 10
DC CHARACTERISTICS (Over Specified Operating Conditions) (Continued) Symbol Description V Output High Voltage OH1 (Quasi-bidirectional Outputs) I Logical 1 Output Current in Reset OH1 not exceed this or device may enter test modes I ...
Page 11
I Max 4 13 Frequency Typ 3 50 Frequency Max Frequency 5 mA IDLE Typ ...
Page 12
AC CHARACTERISTICS (Continued) For user over specified operating conditions Test Conditions Capacitive load on all pins The 80C196KC will meet these specifications Symbol Description F Frequency on XTAL1 (8XC196KC) XTAL F Frequency on XTAL1 (8XC196KC20) XTAL T I ...
Page 13
System Bus Timings 8XC196KC 8XC196KC20 270942 – ...
Page 14
READY Timings (One Wait State) Buswidth Timings 14 270942 – 20 270942 – 35 ...
Page 15
HOLD HLDA Timings Symbol Description T HOLD Setup HVCH T CLKOUT Low to HLDA Low CLHAL T CLKOUT Low to BREQ Low CLBRL T HLDA Low to Address Float HALAZ T HLDA Low to BHE INST RD WR Weakly Driven ...
Page 16
Bus Cycle Type Internal Execution 16-Bit External Execution 8-Bit External Execution EXTERNAL CLOCK DRIVE (8XC196KC) Symbol Parameter 1 T Oscillator Frequency XLXL T Oscillator Period XLXL T High Time XHXX T Low Time XLXX T Rise Time XLXH ...
Page 17
EXTERNAL CLOCK DRIVE (8XC196KC20) Symbol Parameter 1 T Oscillator Frequency XLXL T Oscillator Period XLXL T High Time XHXX T Low Time XLXX T Rise Time XLXH T Fall Time XHXL EXTERNAL CLOCK DRIVE WAVEFORMS EXTERNAL CRYSTAL CONNECTIONS NOTE Keep ...
Page 18
EXPLANATION OF AC SYMBOLS Each symbol is two pairs of letters prefixed by ‘‘T’’ for time The characters in a pair indicate a signal and its condition respectively Symbols represent the time between the two signal condition points ...
Page 19
CHARACTERISTICS The A D converter is ratiometric so absolute accuracy is dependent on the accuracy and stability of V 10-BIT MODE A D OPERATING CONDITIONS Symbol Description T Ambient Temperature Commercial Temp A T Ambient Temperature Extended ...
Page 20
MODE A D OPERATING CONDITIONS Symbol Description T Ambient Temperature Commercial Temp A T Ambient Temperature Extended Temp A V Digital Supply Voltage CC V Analog Supply Voltage REF T Sample Time SAM T Conversion Time CONV ...
Page 21
EPROM SPECIFICATIONS OPERATING CONDITIONS DURING PROGRAMMING Symbol Description T Ambient Temperature During Programming A V Supply Voltage During Programming CC V Reference Supply Voltage During Programming REF V Programming Voltage Pin Voltage EA F Oscillator Frequency During ...
Page 22
DC EPROM PROGRAMMING CHARACTERISTICS Symbol Description I V Supply Current (When Programming NOTE Do not apply V until V is stable and within specifications and the oscillator clock has stabilized or the device may be PP ...
Page 23
SLAVE PROGRAMMING MODE TIMING IN DATA PROGRAM WITH REPEATED PROG PULSE AND AUTO INCREMENT 8XC196KB TO 8XC196KC DESIGN CONSIDERATIONS 1 Memory Map The 8XC196KC has 512 bytes of RAM SFRs and an optional ROM OTPROM The extra 256 bytes of ...
Page 24
DATA SHEET REVISION HISTORY This data sheet is valid for devices with a ‘‘H’’ ‘‘L’’ or ‘‘M’’ at the end of the topside tracking number The topside tracking number consists of nine characters and is the second line ...
Page 25
T (MAX) is now specified at HAHBV 33 The T and T specifications were removed These specifications are not required in high-speed LLYV LLGV systems designs 34 Added EXTINT P0 7 errata to Errata section The following are the ...