ISL59481IRZ-T13 Intersil, ISL59481IRZ-T13 Datasheet - Page 9

IC MUX AMP DUAL 500MHZ 48-QFN

ISL59481IRZ-T13

Manufacturer Part Number
ISL59481IRZ-T13
Description
IC MUX AMP DUAL 500MHZ 48-QFN
Manufacturer
Intersil
Datasheet

Specifications of ISL59481IRZ-T13

Applications
4:1 Multiplexer-Amplifier
Number Of Circuits
3
-3db Bandwidth
500MHz
Slew Rate
870 V/µs
Current - Supply
92mA
Current - Output / Channel
135mA
Mounting Type
Surface Mount
Package / Case
48-VQFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
V+ SUPPLY
V- SUPPLY
If positive voltages are applied to the logic or analog video
input pins before V+ is applied, current will flow through the
internal ESD diodes to the V+ pin. The presence of large
decoupling capacitors and the loading effect of other circuits
connected to V+, can result in damaging currents through
the ESD diodes and other active circuits within the device.
Therefore, adequate current limiting on the digital and
analog inputs is needed to prevent damage during the time
the voltages on these inputs are more positive than V+.
HIZ State
Each internal 4:1 triple MUX-amp has a three-state output
control pin (HIZ1 and HIZ2). Each has an internal pull-down
resistor to set the output to the enabled state with no
connection to the HIZ pin. The HIZ state is established within
approximately 15ns by placing a logic high (>2V) on the HIZ
pin. If the HIZ state is selected, the output is a high impedance
1.4MΩ with approximately 1.5pF in parallel with a 10μA bias
current from the output. When more than one MUX shares a
common output, the high impedance state loading effect is
minimized over the maximum output voltage swing and
maintains its high Z even in the presence of high slew rates.
The supply current during this state is the same as the active
state.
EN and Power-down States
The EN pin is active low. An internal pull-down resistor
ensures the device will be active with no connection to the
EN pin. The power-down state is established within
approximately 80ns, if a logic high (>2V) is placed on the EN
pin. In the power-down state, supply current is reduced
significantly by shutting the three amplifiers off. The output
presents a high impedance to the output pin, however, there
is a risk that the disabled amplifier output can be back-driven
at signal voltage levels exceeding ~2V
condition, large incoming slew rates can cause fault currents
of tens of mA. Therefore, the parallel connection of multiple
outputs is not recommended unless the application can
tolerate the limited power-down output impedance.
Limiting the Output Current
No output short circuit current limit exists on these parts. All
applications need to limit the output current to less than 50mA.
Adequate thermal heat sinking of the parts is also required.
POWER
SIGNAL
LOGIC
DE-COUPLING
GND
CAPS
9
PROTECTION
SCHOTTKY
P-P
. Under this
FIGURE 16. SCHOTTKY PROTECTION CIRCUIT
GND
S0
IN0
IN1
V+
V-
V+
V-
V+
V-
PC Board Layout
The AC performance of this circuit depends greatly on the
care taken in designing the PC board. The following are
recommendations to achieve optimum high frequency
performance from your PC board.
• The use of low inductance components, such as chip
• Minimize signal trace lengths. Trace inductance and
• Match channel-to-channel analog I/O trace lengths and
• Maximize use of AC de-coupled PCB layers. All signal I/O
• Use proper value and location of termination resistors.
• When testing, use good quality connectors and cables,
• A minimum of 2 power supply decoupling capacitors are
• The NIC pins are placed on both sides of the input pins.
V+
V-
resistors and chip capacitors, is strongly recommended.
capacitance can easily limit circuit performance. Avoid
sharp corners. Use rounded corners when possible. Vias
in the signal lines add inductance at high frequency and
should be avoided. PCB traces greater than 1" begin to
exhibit transmission line characteristics with signal rise/fall
times of 1ns or less. High frequency performance may be
degraded for traces greater than one inch, unless
controlled impedance (50Ω or 75Ω) strip lines or
microstrips are used.
layout symmetry. This will minimize propagation delay
mismatches.
lines should be routed over continuous ground planes (i.e. no
split planes or PCB gaps under these lines). Avoid vias in the
signal I/O lines.
Termination resistors should be as close to the device as
possible.
matching cable types and keeping cable lengths to a
minimum.
recommended (1000pF, 0.01µF) as close to the devices as
possible. Avoid vias between the cap and the device
because vias add unwanted inductance. Larger caps can be
farther away. When vias are required in a layout, they should
be routed as far away from the device as possible.
These pins are not internally connected to the die. It is
recommended these pins be tied to ground to minimize
crosstalk.
CONTROL
LOGIC
V+
V-
OUT
May 18, 2007
EXTERNAL
CIRCUITS
FN6208.4

Related parts for ISL59481IRZ-T13