ATmega640 Atmel Corporation, ATmega640 Datasheet - Page 336

• Manufacturer Part Number: ATmega640
• Manufacturer: Atmel Corporation

Specifications of ATmega640

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 86
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 1
• Uart: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 16
• Input Capture Channels: 4
• Pwm Channels: 15
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

30.2
2549N–AVR–05/11
Fuse Bits
Table 30-2.
Notes:
The ATmega640/1280/1281/2560/2561 has three Fuse bytes.
page 337
Fuse bytes. Note that the fuses are read as logical zero, “0”, if they are programmed.
Table 30-3.
Note:
BLB1 Mode
Extended Fuse Byte
BODLEVEL2
BODLEVEL1
BODLEVEL0
1
2
3
4
1. Program the Fuse bits and Boot Lock bits before programming the LB1 and LB2.
2. “1” means unprogrammed, “0” means programmed.
1. See
Memory Lock Bits
describe briefly the functionality of all the fuses and how they are mapped into the
–
–
–
–
–
Lock Bit Protection Modes
Extended Fuse Byte
“System and Reset Characteristics” on page 372
BLB12
(1)
(1)
(1)
1
1
0
0
BLB11
1
0
0
1
Bit No
ATmega640/1280/1281/2560/2561
7
6
5
4
3
2
1
0
Protection Type
No restrictions for SPM or (E)LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section, and
(E)LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
(E)LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
Brown-out Detector trigger level
Brown-out Detector trigger level
Brown-out Detector trigger level
(1)(2)
(Continued)
Description
–
–
–
–
–
for BODLEVEL Fuse decoding.
Table 30-3
through
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
Default Value
Table 30-5 on
1
1
1
1
1
336