ATtiny167 Automotive Atmel Corporation, ATtiny167 Automotive Datasheet - Page 119

• Manufacturer Part Number: ATtiny167 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATtiny167 Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

12.7
7728G–AVR–06/10
Output Compare Units
The 16-bit comparator continuously compares TCNT1 with the Output Compare Register
(OCR1A/B). If TCNT equals OCR1A/B the comparator signals a match. A match will set the
Output Compare Flag (OCF1A/B) at the next timer clock cycle. If enabled (OCIE1A/B = 1), the
Output Compare Flag generates an Output Compare interrupt. The OCF1A/B flag is automati-
cally cleared when the interrupt is executed. Alternatively the OCF1A/B flag can be cleared by
software by writing a logical one to its I/O bit locations. The Waveform Generator uses the
match signal to generate an output according to operating mode set by the Waveform Gener-
ation mode (WGM13:0) bits and Compare Output mode (COM1A/B1:0) bits. The TOP and
BOTTOM signals are used by the Waveform Generator for handling the special cases of the
extreme values in some modes of operation
A special feature of Output Compare unit A allows it to define the Timer/Counter TOP value
(i.e., counter resolution). In addition to the counter resolution, the TOP value defines the
period time for waveforms generated by the Waveform Generator.
Figure 12-4
gram that are not directly a part of the Output Compare unit are gray shaded.
Figure 12-4. Output Compare Unit, Block Diagram
The OCR1A/B Register is double buffered when using any of the twelve Pulse Width Modula-
tion (PWM) modes. For the Normal and Clear Timer on Compare (CTC) modes of operation,
the double buffering is disabled. The double buffering synchronizes the update of the
OCR1A/B Compare Register to either TOP or BOTTOM of the counting sequence. The syn-
chronization prevents the occurrence of odd-length, non-symmetrical PWM pulses, thereby
making the output glitch-free.
shows a block diagram of the Output Compare unit. The elements of the block dia-
OCRnxH Buf.(8-bit)
OCRnxH (8-bit)
BOTTOM
OCRnx Buffer (16-bit Register)
TEMP (8-bit)
TOP
OCRnx (16-bit Register)
OCRnxL Buf.(8-bit)
OCRnxL (8-bit)
DATA BUS
(See “Modes of Operation” on page
Waveform Generator
WGMn3:0
=
(16-bit Comparator )
(8-bit)
COMnx1:0
ATtiny87/ATtiny167
TCNTnH (8-bit)
OCFnx
TCNTn (16-bit Counter)
(Int.Req.)
TCNTnL (8-bit)
122.)
OCnxW
OCnxX
OCnxU
OCnxV
119