ATtiny167 Automotive Atmel Corporation, ATtiny167 Automotive Datasheet - Page 221

• Manufacturer Part Number: ATtiny167 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATtiny167 Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

20.2.4
7728G–AVR–06/10
Reading the Signature Row from Software
Similarly, when reading the Extended Fuse byte (EFB), load 0x0002 in the Z-pointer. When an
LPM instruction is executed within three cycles after the RFLB and SPMEN bits are set in the
SPMCSR, the value of the Extended Fuse byte will be loaded in the destination register as
shown below. See
Extended Fuse byte.
Fuse and Lock bits that are programmed, will be read as zero. Fuse and Lock bits that are
unprogrammed, will be read as one.
To read the Signature Row from software, load the Z-pointer with the signature byte address
given in
LPM instruction is executed within three CPU cycles after the SIGRD and SPMEN bits are set
in SPMCSR, the signature byte value will be loaded in the destination register. The SIGRD
and SPMEN bits will auto-clear upon completion of reading the Signature Row Lock bits or if
no LPM instruction is executed within three CPU cycles. When SIGRD and SPMEN are
cleared, LPM will work as described in the Instruction set Manual.
Table 20-1.
Note:
Bit
Rd (Z=0x0002)
8MHz RC Oscillator Calibration Byte
TSOFFSET - Temp Sensor Offset
All other addresses are reserved for future use.
Table 20-1 on page 221
TSGAIN - Temp Sensor Gain
Device Signature Byte 0
Device Signature Byte 1
Device Signature Byte 2
Signature Row Addressing
Signature Byte
7
–
Table 21-3 on page 226
6
–
and set the SIGRD and SPMEN bits in SPMCSR. When an
5
–
4
–
for detailed description and mapping of the
3
–
ATtiny87/ATtiny167
Z-Pointer Address
2
–
0x0000
0x0002
0x0004
0x0001
0x0005
0x0007
1
–
EFB0
0
221