ATxmega32A4 Atmel Corporation, ATxmega32A4 Datasheet - Page 217

• Manufacturer Part Number: ATxmega32A4
• Manufacturer: Atmel Corporation

Specifications of ATxmega32A4

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 7
• Twi (i2c): 2
• Uart: 5
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 4
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 16
• Pwm Channels: 16
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.8
19.8.1
19.9
19.9.1
8077H–AVR–12/09
Register Description - TWI
Register Description - TWI Master
CTRL– TWI Common Control Register
CTRLA - TWI Master Control Register A
• Bit 7:2 - Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
• Bit 1
SCL.
• Bit 0 - EDIEN: External Driver Interface Enable
Setting this bit enables the use of the external driver interface, clearing this bit enables normal
two wire mode. See
Table 19-1.
• Bit 7:6 - INTLVL[1:0]: Interrupt Level
The Interrupt Level (INTLVL) bit select the interrupt level for the TWI master interrupts.
• Bit 5 - RIEN: Read Interrupt Enable
Setting the Read Interrupt Enable (RIEN) bit enables the Read Interrupt when the Read Interrupt
Flag (RIF) in the STATUS register is set. In addition the INTLVL bits must be unequal zero for
TWI master interrupts to be generated.
Setting this bit to one enables an internal hold time on SDA with respect to the negative edge of
Bit
+0x00
Read/Write
Initial Value
Bit
+0x00
Read/Write
Initial Value
EDIEN
0
1
- SDAHOLD: SDA Hold Time Enable.
Mode
Normal TWI
External Driver
Interface
R/W
7
R
0
7
0
-
External Driver Interface Enable
INTLVL[1:0]
Table 19-1
R/W
6
R
0
6
0
-
Comment
Two pin interface,
Slew rate control and input filter.
Four pin interface,
Standard I/O, no slew-rate control, no input filter.
for details.
RIEN
R/W
R
5
0
5
0
-
WIEN
R/W
R
4
0
4
0
-
ENABLE
R/W
R
3
0
3
0
-
R
R
2
0
2
0
-
-
SDAHOLD
R/W
R
1
0
1
0
-
XMEGA A
EDIEN
R/W
R
0
0
0
0
-
CTRLA
CTRL
217