ATxmega64A3U Atmel Corporation, ATxmega64A3U Datasheet - Page 209

• Manufacturer Part Number: ATxmega64A3U
• Manufacturer: Atmel Corporation

Specifications of ATxmega64A3U

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 50
• Ext Interrupts: 50
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 10
• Twi (i2c): 2
• Uart: 7
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 7
• Output Compare Channels: 22
• Input Capture Channels: 22
• Pwm Channels: 22
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

16.7.4
8331A–AVR–07/11
STATUS – Status Register
• Bit 7:5 – Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
• Bit 4 – FDDBD: Fault Detection on Debug Break Detection
By default, when this bit is cleared and fault protection is enabled, and OCD break request is
treated as a fault. When this bit is set, an OCD break request will not trigger a fault condition.
• Bit 3 – Reserved
This bit is unused and reserved for future use. For compatibility with future devices, always write
this bit to zero when this register is written.
• Bit 2 – FDMODE: Fault Detection Restart Mode
This bit sets the fault protection restart mode. When this bit is cleared, latched mode is used,
and when it is set, cycle-by-cycle mode is used.
In latched mode, the waveform output will remain in the fault state until the fault condition is no
longer active and the FDF has been cleared by software. When both conditions are met, the
waveform output will return to normal operation at the next UPDATE condition.
In cycle-by-cycle mode, the waveform output will remain in the fault state until the fault condition
is no longer active. When this condition is met, the waveform output will return to normal opera-
tion at the next UPDATE condition
• Bit 1:0 – FDACT[1:0]: Fault Detection Action
These bits define the action performed, according to
detected.
Table 16-1.
• Bit 7:3 – Reserved
These bits are reserved and will always be read as zero. For compatibility with future devices,
always write these bits to zero when this register is written.
Bit
+0x04
Read/Write
Initial Value
FDACT[1:0]
00
01
10
11
Fault actions
R
7
–
0
Group Configuration
R
6
–
0
CLEARDIR
NONE
R
5
–
0
.
R
4
–
0
Description
None (fault protection disabled)
Reserved
Reserved
Clear all direction (DIR) bits which correspond to the
enabled DTI channel(s); i.e., tri-state the outputs
R
3
–
0
Atmel AVR XMEGA AU
Table
FDF
R/W
2
0
16-1, when a fault condition is
DTHSBUFV
R/W
1
0
DTLSBUFV
R/W
0
0
STATUS
209