ST72262G1 STMicroelectronics, ST72262G1 Datasheet - Page 31

• Manufacturer Part Number: ST72262G1
• Description: 8-BIT MCU WITH FLASH OR ROM MEMORY, ADC, TWO 16-BIT TIMERS, I2C, SPI, SCI INTERFACES
• Manufacturer: STMicroelectronics

Specifications of ST72262G1

• 4 K Or 8 Kbytes Program Memory: ROM or single voltage extended Flash (XFlash) with read-out protection, write protection, In-Circuit Programming and In-Application Programming (ICP and IAP). 10K write/erase cycles guaranteed, data retention
• Clock Sources: crystal/ceramic resonator oscillators, internal RC oscillator and bypass for external clock
• 4 Power Saving Modes: Halt, Active Halt,Wait and Slow
• Two 16-bit Timers With: 2 input captures, 2 output compares, external clock input on one timer, PWM and Pulse generator modes

INTERRUPTS (Cont’d)
7.5 INTERRUPT REGISTER DESCRIPTION
CPU CC REGISTER INTERRUPT BITS
Read/Write
Reset Value: 111x 1010 (xAh)
Bit 5, 3 = I1, I0 Software Interrupt Priority
These two bits indicate the current interrupt soft-
ware priority.
These two bits are set/cleared by hardware when
entering in interrupt. The loaded value is given by
the corresponding bits in the interrupt software pri-
ority registers (ISPRx).
They can be also set/cleared by software with the
RIM, SIM, HALT, WFI, IRET and PUSH/POP in-
structions (see “Interrupt Dedicated Instruction
Set” table).
*Note: TRAP and RESET events are non maska-
ble sources and can interrupt a level 3 program.
Level 0 (main)
Level 1
Level 2
Level 3 (= interrupt disable*)
Interrupt Software Priority
7
1
1
I1
H
I0
Level
High
Low
N
I1
1
0
0
1
Z
I0
0
1
0
1
C
0
INTERRUPT SOFTWARE PRIORITY REGIS-
TERS (ISPRX)
Read/Write (bits 7:4 of ISPR3 are read only)
Reset Value: 1111 1111 (FFh)
These four registers contain the interrupt software
priority of each interrupt vector.
– Each interrupt vector (except RESET and TRAP)
– Each I1_x and I0_x bit value in the ISPRx regis-
– Level 0 can not be written (I1_x=1, I0_x=0). In
The RESET and TRAP vectors have no software
priorities. When one is serviced, the I1 and I0 bits
of the CC register are both set.
Caution: If the I1_x and I0_x bits are modified
while the interrupt x is executed the following be-
haviour has to be considered: If the interrupt x is
still pending (new interrupt or flag not cleared) and
the new software priority is higher than the previ-
ous one, the interrupt x is re-entered. Otherwise,
the software priority stays unchanged up to the
next interrupt request (after the IRET of the inter-
rupt x).
has corresponding bits in these registers where
its own software priority is stored. This corre-
spondance is shown in the following table.
ters has the same meaning as the I1 and I0 bits
in the CC register.
this case, the previously stored value is kept. (ex-
ample: previous=CFh, write=64h, result=44h)
ISPR0
ISPR1
ISPR2
ISPR3
Vector Address
FFFBh-FFFAh
ST72260Gx, ST72262Gx, ST72264Gx
FFE1h-FFE0h
FFF9h-FFF8h
I1_11 I0_11 I1_10 I0_10 I1_9
I1_3
I1_7
7
1
...
I0_3
I0_7
1
I1_2
I1_6
1
I0_2
I0_6
1
I1_13 I0_13 I1_12 I0_12
I1_1
I1_5
ISPRx Bits
Not used
I0_1
I0_5
I0_9
ei0
ei1
...
I1_0
I1_4
I1_8
31/172
I0_0
I0_4
I0_8
0