OM6213 NXP Semiconductors, OM6213 Datasheet
OM6213
Related parts for OM6213
OM6213 Summary of contents
Page 1
... DATA SHEET OM6213 48 84 pixels matrix LCD driver Product specification File under Integrated Circuits, IC17 INTEGRATED CIRCUITS 2001 Nov 07 ...
Page 2
... LCDSENSE 20.1 20.2 20.3 20.4 20.5 20.6 20 Product specification OM6213 Display Control D, E Set Y address of RAM Set X address of RAM Temperature Control Bias value: V generator LCD TEMPERATURE COMPENSATION LIMITING VALUES HANDLING DC CHARACTERISTICS AC CHARACTERISTICS SERIAL INTERFACE RESET APPLICATION INFORMATION MODULE MAKER PROGRAMMING ...
Page 3
... APPLICATIONS Telecommunications equipment. 3 GENERAL DESCRIPTION The OM6213 is a low power CMOS LCD controller driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption ...
Page 4
... LCD DISPLAY DATA RAM (DDRAM bits ADDRESS COUNTER DATA REGISTER I/O BUFFER SDIN SCLK Fig.1 Block diagram. 4 Product specification ROW 0 to ROW 47 48 ROW DRIVERS SHIFT REGISTER RESET OSCILLATOR TIMING GENERATOR DISPLAY ADDRESS COUNTER OM6213 MGT840 D/C SCE OM6213 RES OSC ...
Page 5
... PR is also used for HV-gen programming. LCDIN OS0 OS4 offset. Each pin must be LCD , which corresponds to logic SS1 , which corresponds to logic 1. All five pins define decimal (00000). The register SS1 OM6213 : LCD power generator LCD LCDSENSE generator LCD ...
Page 6
... Table 2). 8.6 LCD row and column drivers , the SS1 The OM6213 contains 48 rows and 84 column drivers, which connect the appropriate LCD bias voltages in sequence to the display in accordance with the data to be displayed. Figure 2 shows typical waveforms. Unused outputs should be left unconnected. ...
Page 7
... V (t) = C1(t) R0(t) state1 V (t) = C1(t) R1(t) state2 2001 Nov 07 frame n frame n ... 8... Fig.2 Typical LCD driver waveforms. 7 Product specification OM6213 1 V state1 (t) V state2 ( SS1 LCD V LCD ...
Page 8
... Philips Semiconductors 48 84 pixels matrix LCD driver bank 0 bank 1 bank 2 bank 3 bank 4 bank 5 2001 Nov 07 DDRAM LCD MGT842 Fig.3 DDRAM to display mapping. 8 Product specification OM6213 top of LCD R0 R8 R16 R24 R32 R40 R47 ...
Page 9
... DD1 V (or higher) according to t DD(min) Fig.16). 10 ADDRESSING Data is downloaded in bytes into the RAM matrix of the OM6213 as indicated in Figs. and 6. The display RAM has a matrix bits. The columns are addressed by the address pointer. 10.1 Data structure handbook, full pagewidth LSB ...
Page 10
... Fig.6 Sequence of writing data bytes into RAM with horizontal addressing (V = 0). 2001 Nov 07 X address 2 86 170 254 338 422 X address 10 Product specification OM6213 0 Y address 503 5 83 MGT844 0 Y address 503 5 83 MGT845 ...
Page 11
... The level of the D/C signal is read during the last bit of the data byte. Instructions can be sent in any order to the OM6213 (the exception being that the temperature control command must be followed by at least one byte of data or command). ...
Page 12
... DB3 Fig.9 Serial bus protocol; transmission of one byte. DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Fig.11 Serial bus reset function (SCE). 12 Product specification OM6213 DB2 DB1 DB0 MGT641 DB7 DB6 DB5 ...
Page 13
... Sets X address part of RAM reserved set temperature coefficient (TCx reserved BS BS set bias system (BSx reserved V V write V to register PR2 PR1 PR0 PR Product specification OM6213 MGT644 ...
Page 14
... Set X address of RAM The X address points to the columns. The range (53H). 11.6 Temperature Control The temperature coefficient of V bits TC1 and TC0. 14 Product specification OM6213 LOGIC 1 chip is in Power-down mode vertical addressing use extended instruction set Y1 Y0 CONTENT 0 ...
Page 15
... Different multiplex rates ----------------- RECOMMENDED MUX RATE 100 18 10 BIAS VOLTAGE FOR BIAS SYSTEM 8 V LCD LCD LCD LCD LCD V SS OM6213 ...
Page 16
... TCD 3.62 3.37 26.1 28 0.58 0. 110 120 5.18 5.56 9.35 10.11 . Under all conditions and including all tolerances the measured V CUT LCD is then 4 decimal (11100 binary OS Product specification OM6213 T T – (3) CUT , LCD register PR can be calculated 6.06 V (4) th UNIT decimal decimal 6.9 V. The user ...
Page 17
... V , not all V OS CAL = external V supply is provided. LCD LCD Fig.13 V programming of the OM6213. LCD 17 Product specification DECIMAL BINARY 1 11111 2 11110 3 11101 4 11100 5 11011 6 11010 7 11001 8 11000 ...
Page 18
... MOS devices (see “Handling MOS devices” ). 2001 Nov function of liquid crystal temperature (typical values). LCD PARAMETER 18 Product specification must be increased LCD for high multiplex rates. In the OM6213 the LCD MGT848 T MIN. MAX. 0.5 +6.5 0.5 +6 ...
Page 19
... V i DD1 SS note 6 note 6 note 7 19 Product specification MIN. TYP. 2.5 3.3 2.5 3.3 4.5 9.0 120 or DD1 DD1 DD1 V 0.3V SS 0.7V V DD1 100 0 +100 100 0 +100 70 +70 OM6213 MAX. UNIT DD1 V DD1 ...
Page 20
... LCDOUT +85 C; unless otherwise specified. MIN. TYP. 30.9 34 100 0 250 100 100 60 100 100 100 100 100 100 100 or higher V VHRL DD1,2,3 OM6213 MAX. UNIT 37.7 kHz 1000 ns 4.00 MHz reduces t ). ...
Page 21
... RESET handbook, full pagewidth V DD1 RES V DD1 RES SCE 2001 Nov PWH1 Fig.15 Serial interface timing VHRL t RW Fig.16 Reset timing. 21 Product specification PWH2 cy(SCLK R(op) MGT850 OM6213 MGT849 ...
Page 22
... Philips Semiconductors 48 84 pixels matrix LCD driver 19 APPLICATION INFORMATION Table 8 Example of OM6213 operation SERIAL BUS BYTE STEP D/C DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 1 Start ...
Page 23
... The pinning of the OM6213 is optimized for single plane wiring e.g. for chip-on-glass display modules. Display size pixels. handbook, full pagewidth The required minimum value for the external capacitors in an application with the OM6213 are 100 nF (min.) for V ...
Page 24
... Philips Semiconductors 48 84 pixels matrix LCD driver 20 Module Maker programming The OM6213 features five Module Maker programmable parameters calibration LCD 2. Charge pump multiplication factor 3. Bias system selected when BS[2:0] = 100 4. V temperature coefficient selected when LCD TC[1: (TC1) 5. Seal bit. Used to select the use of the default parameters or the Module Maker programmable parameters ...
Page 25
... Bias system selected when BS[2:0] = 100 definition BS 00 BIAS SYSTEM 1 0 (default temperature coefficient selected when LCD TC[1: (TC1) LCD temperature coefficient LCD TC[1:0] TC1[1: OM6213 temperature V LCD TEMPERATURE COEFFICIENT TCA TCB (default) TCA TCD TCC TCC TCD ...
Page 26
... An unprogrammed cell contains 0. A programmed cell contains 1. OM6213 dice are shipped to the Module Maker with all cells unprogrammed (containing 0). An unprogrammed cell may be programmed by using the described procedure. A programmed cell cannot be unprogrammed to 0. 2001 Nov 07 PARAMETERS defaults Module Maker programmable 26 Product specifi ...
Page 27
... CELL[ CELL[ Product specification OM6213 ACTION switch power on reset the device (RES pulse) exit Power-down and set instruction set wait 5 ms enter Power-down enter programming mode specify CELL[9] (V [4]) CAL specify CELL[8] (V [3]) CAL ...
Page 28
... SDIN = 0) when the Product specification MIN. TYP. MAX DD1 9 9 DD2 850 1000 100 200 100 120 200 pin is being driven. LCDIN OM6213 UNIT ...
Page 29
... PR3 PR2 PR1 PR0 Product specification OM6213 t h;SCLK DB7 DB6 t h;SDIN MGT853 ACTION switch power on reset the device (RES pulse) configure the device and fill in the DDRAM without switching the charge pump on exit Power-down and set instruction ...
Page 30
... CELL[ ( set instruction set (exit programming mode) V set V and switch charge pump on PR0 PR measure V LCD 0 switch charge pump off not correct, go back to step 2 LCD and try a different V CAL switch power off store V [4:0] for programming later CAL OM6213 [4:0] ...
Page 31
... Philips Semiconductors 48 84 pixels matrix LCD driver 21 CHIP INFORMATION The OM6213 is manufactured in n-well CMOS technology. 22 BONDING PAD INFORMATION Table 19 Bonding pad information NAME Pad pitch Pad size, aluminium CBB opening Bump dimensions Wafer thickness (excluding bumps) 9.11 mm handbook, halfpage 1.78 OM6213 Fig.20 Bonding pads. ...
Page 32
... V LCDIN 820 +880 V LCDOUT 820 +670 V LCDOUT 820 +600 V LCDOUT 820 +530 V LCDOUT 820 +460 V LCDOUT 820 +390 32 Product specification OM6213 COORDINATES PAD 820 +320 38 820 +250 39 820 +180 40 820 +110 41 820 100 42 820 310 43 820 520 44 820 ...
Page 33
... COL 35 +825 2695 COL 36 +825 2635 COL 37 +825 2575 COL 38 +825 2395 COL 39 +825 2335 COL 40 33 Product specification OM6213 COORDINATES PAD x y 115 +825 2275 116 +825 2215 117 +825 2155 118 +825 2095 119 +825 2035 ...
Page 34
... ROW 33 +825 +2105 ROW 34 +825 +2165 ROW 35 +825 +2225 Dummy pad +825 +2285 Dummy pad +825 +2345 34 Product specification OM6213 COORDINATES PAD x y 189 +825 +2405 190 +825 +2465 191 +825 +2525 192 +825 +2585 193 +825 +2645 ...
Page 35
... V DD2 SCLK T7 y SDIN D SCE x OSC V SS2 SS1 OM6213 V LCDIN V LCDOUT V LCDSEN RES alignment mark dummy pad MGT856 Fig.22 Pad locations. 35 Product specification OM6213 dummy pad ROW ROW 24 ROW ROW 47 COL COL 56 COL COL 28 COL ...
Page 36
... The conditions for continuity test are as follows: Maximum forward current = 5 mA; Maximum reverse voltage = 5 V. 2001 Nov 07 V DD2 V SS1 V SS2 V LCDIN , V LCDSENSE V SS1 V LCDIN V SS1 SDIN SS1 Fig.23 Device protection diagram. 36 Product specification OM6213 V DD3 V SS1 V LCDOUT V SS1 MGT858 ...
Page 37
... J tray thickness K tray cross section L tray cross section pocket depth x number of pockets in x direction y number of pockets in y direction OM6213 VALUE 14.45 mm 3.76 mm 9.31 mm 1.98 mm 50.8 mm 50.8 mm 10.95 mm 4.72 mm 3.96 mm 1.78 mm 2. ...
Page 38
... Product specification OM6213 DEFINITIONS These products are not Philips Semiconductors ...
Page 39
... Philips Semiconductors 48 84 pixels matrix LCD driver 2001 Nov 07 NOTES 39 Product specification OM6213 ...
Page 40
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2001 All rights are reserved. Reproduction in whole or in part is prohibited ...