OM6213 NXP Semiconductors, OM6213 Datasheet - Page 27

• Manufacturer Part Number: OM6213
• Description: Om6213 48 X 84 Pixels Matrix Lcd Driver
• Manufacturer: NXP Semiconductors

Philips Semiconductors
Table 15 Module Maker parameters programming procedure
Notes
1. Programming voltages are applied via pins SDIN and VLCDIN.
2. It is possible to program only one cell at a time. When applying programming waveforms, all cells (except the one
3. The seal bit (SB) must be the last to be programmed, since no further programming is possible when SB = 1.
4. If the seal bit is unprogrammed (SB = 0) the defaults (and not the Module Maker programmed parameters) are taken
5. Example: a device has to be programmed to use a charge pump with a multiplication factor equal to 3 (initial state is
6. Programming waveforms MUST only be applied at step 17.
2001 Nov 07
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
STEP D/C
48
being programmed) should be 0; see also example in note 5.
into account.
MF = SB = 0, final state is MF = SB = 1).
a) Execute steps 1 to 6.
b) Set CELL[9:0] to 0000010000 (steps 7 to 16).
c) Apply programming waveforms (step 17): MF cell is now programmed (MF = 1, SB = 0).
d) Go back to step 7.
e) Set CELL[9:0] to 0000000001 (steps 7 to 16).
f) Apply programming waveforms (step 17): SB cell is now programmed (MF = SB = 1).
g) Execute steps 18 to 20.
84 pixels matrix LCD driver
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DB7 DB6 DB5 DB4 DB3 DB2 DB1
0
0
0
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
COMMAND BYTE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
27
CELL[9]
CELL[8]
CELL[7]
CELL[6]
CELL[5]
CELL[4]
CELL[3]
CELL[2]
CELL[1]
CELL[0]
DB0
0
0
1
0
switch power on
reset the device (RES pulse)
exit Power-down and set H = 0 instruction set
wait 5 ms
enter Power-down
enter programming mode
specify CELL[9] (V
specify CELL[8] (V
specify CELL[7] (V
specify CELL[6] (V
specify CELL[5] (V
specify CELL[4] (MF)
specify CELL[3] (BS100)
specify CELL[2] (TC1[1])
specify CELL[1] (TC1[0])
specify CELL[0] (SB)
apply programming waveforms
go back to step 7 if other cells need to be
programmed (see note 5)
exit programming mode
switch power off
CAL
CAL
CAL
CAL
CAL
ACTION
[4])
[3])
[2])
[1])
[0])
Product specification
OM6213