ISL36356A Intersil Corporation, ISL36356A Datasheet - Page 4

• Manufacturer Part Number: ISL36356A
• Description: Prism 11Mbps Wireless Local Area Network Access Point
• Manufacturer: Intersil Corporation

The ISL36356A is shipped with U.S.-compliant firmware. In
order to ensure regulatory-compliant channel usage in a
particular country, special geographic-specific firmware is
available for customer production assemblies which restricts
channel usage. An example is ETSI-compliant firmware.
Since the end user does not have the ability to alter this
firmware, regulatory compliance is ensured.
Agency and Regulatory Body Approvals
The WLAN AP will comply to the standards shown in Table 3:
FCC Information to User
This product does not contain any user-serviceable
components and must be used with approved antennas only.
Any product changes or modifications will invalidate all
applicable regulatory certifications and approvals.
FCC Electronic Emission Notices
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
FCC Radio Frequency Interference statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
USA
Canada
Europe
Japan
COUNTRY
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesirable
operation.
TABLE 3. COMPLIANCE STANDARDS
FCC Part 15, Sec. 15.247,
Sec. 15.107 and 15.109
ICAN RSS-210
EN 60950
EN 301 489-1 V1.2.1 (2000-08)
EN 301 489-17 V1.1.1 (2000-09)
EN 300 328 Part 1 V1.2.2 (2000-07)
EN 300 328 Part 2 V1.1.1 (2000-07)
ARIB STD-T66
ARIB STD-33
APPROVAL
4
Grant obtained
Designed for
compliance
Certified
Designed for
compliance
ISL36356A-APBK-EVAL
NOTES
Operation of this equipment in a residential area may cause
harmful interference in which case the user will be required
to correct the interference at his or her own expense.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit different
• Consult the dealer or an experienced radio/TV technician
FCC Guidelines for Human Exposure
The EIRP was measured for the lower, middle and highest
frequencies used by the transmitter. The results in Table 4
are based on a safe distance between antenna and
operator of eight inches.The equipment therefore fulfills the
requirements on power density for general population/
uncontrolled exposure of 1.0mW/cm
the requirements of FCC Part 15.247 (b) (4) and FCC OET
Bulletin 65 including supplements A, B and C.
CAUTION: Any changes or modifications of equipment not expressly
approved by Intersil could void the user’s authority to operate the equipment.
WARNING:
of at least 20 cm must be maintained between the antennas of this device and
all persons.
Measured EIRP
(mW)
Calculated Power
Density (mW/cm2)
receiver.
from that to which the receiver is connected.
for help.
TABLE 4. POWER DENSITY CALCULATION
To comply with FCC RF exposure limits, a separation distance
0.051
Ch.1
63.8
2
and so complies with
0.053
Ch.6
66.2
Ch.11
0.055
69.3