st2024c Sitronix Technology Corporation, st2024c Datasheet - Page 53

• Manufacturer Part Number: st2024c
• Description: 24k 8-bit Single Chip Microcontroller
• Manufacturer: Sitronix Technology Corporation

1
The above information is the exclusive intellectual property of Sitronix Technology Corp. and shall not be disclosed, distributed or reproduced
without permission from Sitronix. Sitronix Technology Corp. reserves the right to change this document without prior notice and makes no
warranty for any errors which may appear in this document. Sitronix products are not intended for use in life support, critical care, medical,
safety equipment, or similar applications where products failure could result in injury, or loss of life, or personal or physical harm, or any military
or defense application, or any governmental procurement to which special terms or provisions may apply.
Ver 2.2
1
9
9
.
.
R
Version2.2
Version2.1
Version2.0
Version1.9
Version 1.5 Page 1
Version 1.4
Version E1.0 Page41 Adding Measure Condition on TABLE 15-34:
Version E0.6 Page45 Modifying FIGURE 17-25:
Version E0.5 Page1
Version E0.4 -Page40 Filling the LCD power consumption table TABLE 15-34: .
Version E0.3 -Page3
Version E0.2 -Page40 Modify the register LCK[2:0] ………………………………..………………………….2002/10/11
Version E0.1 -Page8
R
Version 1.6 Page45
Version 1.8 Page 1
Version 1.7 Page51
E
E
V
V
I
I
S
S
E
E
Page36
Page49/5051 add checklist……………………………………………………………..2006/02/08
Page 28/31/33/34 take
Page12
S
Page22,23 Change register SYS bit4 TEST to Test bit and must be set “0”
Page41, Modify driving strength level 0~31 in heavy mode
Page48, Modify standby current 1~5 in heavy mode
Page50, Remove Item 28 normal mode in checklist…………….….………………………2006/8/1
Page 22
Page 41
Page 45 Modifying DC Characteristic
Page 47/48 Modifying Application Circuit (1000P 100P)………………………………….…2003/8/4
Page1
Page19/20 Modifying SEGs & COMs output HIGH to FLOAT.
Page47/48 Modifying application circuit……………………………………………………..……2003/4/4
-Page44 Filling the Power consumption table
-Page45
-Page40 Added DRV[ ] of LCD driving strength in address20H & Modify TABLE 15-34: …… 2002/9/2
S
Page49 Add PCB 108 of ST2024C EVB photo
Page50 Add checklist for customer to confirm ST2024C EVB PCB number……………….2007/5/21
Page11 Modify write 0 to IREQ to clear Interrupt request flag ………….…………2008/1/31
Page52 Add system clock regulation in Special Notice 2
Page22 Modify SYS [XSEL] in Table of SYSTEM CONTROL REGISTER…………2007/9/12
Page24 Modify description figure 11-6 to 12-6.
-Page48 Adding bonding description
-Page41 Modify LCK[2:0] of TABLE 15-34: ………………………….……..…………….…2002/12/10
Modifying operation voltage 2.4V~3.4V to 2.4V~3.6V……………………………….2003/4/16
Modifying operation voltage 2.4V~5.2V to 2.4V~3.2V
Added DRV[ ] of LCD driving strength in address20H.
Adding pad location
OSCX work under heavy load mode to support more kinds of 32KHz crystals
Add a note about LCD display quality ……….………………………………………2004/4/7
Adding, FIGURE 17-25: …………………………………………………..………….2003/2/25
modify oscillation start time to OSCX heavy start time
Add CPU clock 250K ~ 2M Hz……………………………………………… 2006/6/23
Add checklist item 29=>after Power on ,enter wait 0 mode 0.5s before normal
operation………………………………………………………………………….2006/5/8
standby current……………………………………………………2005/11/8
modify Two-Pin Two Ended Mode Application Circuit
add pad number and note: all of unused input pins should be pulled up to minimize
remove IR remote controller
off PSG/DAC clock source from oscx
53/54
TABLE 17-39:
ST2024C
1/31/08