isl84467 Intersil Corporation, isl84467 Datasheet - Page 8

• Manufacturer Part Number: isl84467
• Description: Ultra Low On-resistance, +1.65v To +4.5v, Single Supply, Quad Spdt Dual Dpdt Analog Switch
• Manufacturer: Intersil Corporation

.
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to GND (see
Figure 9). To prevent forward biasing these diodes, V+ must
be applied before any input signals, and the input signal
voltages must remain between V+ and GND.
If these conditions cannot be guaranteed, then precautions
must be implemented to prohibit the current and voltage at
the logic pin and signal pins from exceeding the maximum
ratings of the switch. The following two methods can be used
to provide additional protection to limit the current in the
event that the voltage at a signal pin or logic pin goes below
ground or above the V+ rail.
Logic inputs can be protected by adding a 1kΩ resistor in series
with the logic input (see Figure 9). The resistor limits the input
current below the threshold that produces permanent damage,
and the sub-microamp input current produces an insignificant
voltage drop during normal operation.
This method is not acceptable for the signal path inputs.
Adding a series resistor to the switch input defeats the
purpose of using a low
diodes to the signal pins (as shown in Figure 9) will shunt the
fault current to the supply or to ground, thereby protecting
the switch. These Schottky diodes must be sized to handle
the expected fault current.
FIGURE 8. V+ SERIES RESISTOR FOR ENHANCED ESD AND
LATCH-UP IMMUNITY
OPTIONAL
PROTECTION
RESISTOR
NOx
NCx
INx
r
ON
GND
V+
switch. Connecting schottky
100Ω
8
C
COMx
ISL84467
.
Power-Supply Considerations
The ISL84467 construction is typical of most single supply
CMOS analog switches, in that they have two supply pins:
V+ and GND. V+ and GND drive the internal CMOS
switches and set their analog voltage limits. Unlike switches
with a 4.7V maximum supply voltage, the ISL84467 5.5V
maximum supply voltage provides plenty of room for the
10% tolerance of 4.3V supplies, as well as room for
overshoot and noise spikes.
The minimum recommended supply voltage is 1.65V. It is
important to note that the input signal range, switching times,
and ON-resistance degrade at lower supply voltages. Refer to
the “Electrical Specifications” tables starting on page 3 and the
“Typical Performance Curves” starting on page 9 for details.
V+ and GND also power the internal logic and level shifters.
The level shifters convert the input logic levels to switched
V+ and GND signals to drive the analog switch gate
terminals.
This family of switches cannot be operated with bipolar
supplies, because the input switching point becomes
negative in this configuration.
Logic-Level Thresholds
This switch family is 1.8V CMOS compatible (0.5V and 1.4V)
over a supply range of 3.0V to 4.5V (see Figure 19). At 3.0V
the V
CMOS guaranteed low output maximum level of 0.5V, but
noise margin is reduced.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails. Driving
the digital input signals from GND to V+ with a fast transition
time minimizes power dissipation.
The ISL84467 has been designed to minimize the supply
current whenever the digital input voltage is not driven to the
supply rails (0V to V+). For example, driving the device with
2.85V logic (0V to 2.85V) while operating with a 4.2V supply
the device draws only 12μA of current (see Figure 17 for
V
OPTIONAL
PROTECTION
RESISTOR
IN
= 2.85V).
OPTIONAL
SCHOTTKY
DIODE
OPTIONAL
SCHOTTKY
DIODE
IL
level is about 0.53V. This is still above the 1.8V
FIGURE 9. OVERVOLTAGE PROTECTION
V
IN
NX
X
GND
V+
V
COM
July 17, 2007
FN6521.0