isl9211a Intersil Corporation, isl9211a Datasheet
isl9211a
Available stocks
Related parts for isl9211a
isl9211a Summary of contents
Page 1
... NFET quickly when the input is overvoltage in order to remove the power before any damage occurs. The ISL9211A has a logic flag output to indicate a fault condition. The enable input allows the system to cut off the input power if needed. ...
Page 2
... Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp SYMBOL TEST CONDITIONS V Rising POR Falling 24.9k VIN ILIM ISL9211ARU48 OVP ISL9211ARU58 ISL9211ARU68 ISL9211ARU48 ISL9211ARU58 ISL9211ARU68 3V 24.9kΩ OCP VB ILIM 12.4kΩ MAX ILIM BT OCP V BOVP BT BOVP ...
Page 3
... MIN TYP MAX UNITS - - 0 200 - kΩ - 0.4 0 1.5 µA - 170 280 mΩ VIN OUT ISL6292 BATTERY CHARGER C 2 ISL9211A ILIM DISA EN ENA BATT GND FAULT PACK DESCRIPTION 24.9kΩ 200kΩ to 1MΩ 1µF/25V X5R ceramic capacitor FN6702.0 April 2, 2009 ...
Page 4
... Typical Operating Performance VIN(2V/div OUT (2V/DIV) OUT(2V/div) LOAD CURRENT (200mA/DIV) Load Current(200mA/div) TIME - 4ms/DIV FIGURE 2. CAPTURED WAVEFORMS FOR POWER-UP. THE OUTPUT IS LOADED WITH A 10Ω RESISTOR 4 ISL9211A ...
Page 5
... LOAD CURRENT (2A/DIV) Load current (2A/div) FAULT (2V/DIV) Fault(2V/div) TIME - 40µs/DIV FIGURE 8. POWER-UP WAVEFORMS WHEN OUTPUT IS SHORT-CIRCUITED 5 ISL9211A The test conditions for the Typical Operating Performance are 24.9kΩ 200kΩ, Unless Otherwise Noted. (Continued) ILIM VB (2V/DIV) FIGURE 5. TRANSIENT WHEN THE INPUT VOLTAGE STEPS FIGURE 7 ...
Page 6
... TEMPERATURE (°C) FIGURE 12. OVERCURRENT PROTECTION vs TEMPERATURE AT VARIOUS INPUT VOLTAGES FIGURE 14. ON-RESISTANCE vs TEMPERATURE AT DIFFERENT INPUT VOLTAGES 6 ISL9211A The test conditions for the Typical Operating Performance are 24.9kΩ 200kΩ, Unless Otherwise Noted. (Continued) ILIM FIGURE 11. INPUT OVERVOLTAGE PROTECTION vs ...
Page 7
... ISL9211A turned off permanently, as shown in Figure 7. Recycling the input power will reset the counter and restart the ISL9211A. The resistor between the VB pin and the battery, R shown in the Typical Applications circuit important component. This resistor provides a current limit in case the VB pin is shorted to the input voltage under a failure mode ...
Page 8
... AC adapter is inserted live (hot insertion) and the second one is when the current in the power NFET of the ISL9211A has a step-down change. Figure 16 shows an equivalent circuit for the ISL9211A input. The cable between the AC/DC converter output and the handheld system input has a parasitic inductor. The parasitic (EQ ...
Page 9
... In practice, the input decoupling capacitor is recommended to use a 25V, X5R dielectric ceramic capacitor with a value between 0.1µF to 1µF. The output of the ISL9211A and the input of the charging circuit typically share one decoupling capacitor. The selection of that capacitor is mainly determined by the requirement of the charging circuit. When using the ISL6292 family chargers, a 1µ ...
Page 10
... LEAD MICRO THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE (µTDFN) WITH E-PAD Rev 0, 04/08 2.00 6 PIN 1 INDEX AREA (4X) 0.15 TOP VIEW PACKAGE OUTLINE ( 6x0. 8x0.25 ) 0.90 2.00 TYPICAL RECOMMENDED LAND PATTERN 10 ISL9211A 0.25±0.050 ( 8x0. MAX ( 8x0.30 ) 1.60 2.00 C NOTES: 1. Dimensions are in millimeters. Dimensions ...