isl6263c Intersil Corporation, isl6263c Datasheet - Page 16

• Manufacturer Part Number: isl6263c
• Description: 5-bit Vid Single-phase Voltage Regulator With Current Monitor For Gpu Core Power
• Manufacturer: Intersil Corporation

may still need slight adjustment to achieve optimum load line
slope. It is recommended to adjust R
achieved thermal equilibrium at full load.
Dynamic Mode of Operation - Compensation
Parameters
Intersil provides a spreadsheet to calculate the compensator
parameters. Caution needs to be used in choosing the input
resistor to the FB pin. Excessively high resistance will cause
an error to the output voltage regulation due to the bias
current flowing through the FB pin. It is recommended to
keep this resistor below 3kΩ.
Layout Considerations
As a general rule, power should be on the bottom layer of
the PCB and weak analog or logic signals are on the top
layer of the PCB. The ground-plane layer should be adjacent
to the top layer to provide shielding.
Inductor Current Sense and the NTC Placement
It is crucial that the inductor current be sensed directly at the
PCB pads of the sense element, be it DCR sensed or discrete
resistor sensed. The effect of the NTC on the inductor DCR
thermal drift is directly proportional to its thermal coupling with
the inductor and thus, the physical proximity to it.
Signal Ground and Power Ground
The ground plane layer should have a single point connection
to the analog ground at the VSS pin. The VSS island should
be located under the IC package along with the weak analog
traces and components. The paddle on the bottom of the
ISL6263C QFN package is not electrically connected to the
IC, however, it is recommended to make a good thermal
connection to the VSS island using several vias. Connect the
input capacitors, the output capacitors, and the source of the
lower MOSFETs to the power ground plane.
LGATE, PVCC, and PGND
PGND is the return path for the pull-down of the LGATE
low-side MOSFET gate driver. Ideally, PGND should be
connected to the source of the low-side MOSFET with a
low-resistance, low-inductance path. The LGATE trace should
be routed in parallel with the trace from the PGND pin. These
two traces should be short, wide, and away from other traces
because of the high peak current and extremely fast dv/dt.
PVCC should be decoupled to PGND with a ceramic
capacitor physically located as close as practical to the IC
pins.
16
IS2
after the system has
ISL6263C
UGATE, BOOT, and PHASE
PHASE is the return path for the entire UGATE high-side
MOSFET gate driver. The layout for these signals require
similar treatment, but to a greater extent, than those for
LGATE, PVCC, and PGND. These signals swing from
approximately VIN to VSS and are more likely to couple into
other signals.
VSEN and RTN
These traces should be laid out as noise sensitive. For
optimum load line regulation performance, the traces
connecting these two pins to the Kelvin sense leads of the
processor should be laid out away from rapidly rising voltage
nodes, (switching nodes) and other noisy traces. The filter
capacitors C
conjunction with filter resistors R
common mode and differential mode filters, as shown in
Figure 8. The noise environment of the application and
actual board layout conditions will drive the extent of filter
complexity. The maximum recommended resistance for
R
interaction with the 50kΩ input resistance of the remote
sense differential amplifier. The physical location of these
resistors is not as critical as the filter capacitors. Typical
capacitance values for C
range between 330pF to 1000pF and should be placed near
the IC.
RBIAS
The resistor R
the ISL6263C using a noise-free current return path to the
VSS pin.
IMON, SOFT, OCSET, V W, COMP, FB, VDIFF,
ICOMP, ISP, ISN and VO
The traces and components associated with these pins
require close proximity to the IC as well as close proximity to
each other. This section of the converter circuit needs to be
located above the island of analog ground with the
single-point connection to the VSS pin.
Resistor R
Resistor R
between the power ground and the island of analog ground
connected to the VSS pin.
FILTER1
FIGURE 10. TYPICAL POWER COMPONENT PLACEMENT
INDUCTOR
HIGH-SIDE
MOSFETS
and R
S
GROUND
VIAS TO
FILTER1
is preferably located near the boundary
S
PLANE
RBIAS
FILTER2
, C
should be placed in close proximity to
PHASE
NODE
VOUT
FILTER2
GND
VIN
FILTER1
is approximately 10Ω to avoid
, and C
OUTPUT
CAPACITORS
FILTER1
, C
FILTER2
SCHOTTKY
DIODE
LOW-SIDE
MOSFETS
INPUT
CAPACITORS
FILTER3
and R
, and C
FILTER2
used in
FILTER3
July 31, 2008
FN6745.0
form