w9425g6jh Winbond Electronics Corp America, w9425g6jh Datasheet - Page 33
w9425g6jh
Manufacturer Part Number
w9425g6jh
Description
4 M
Manufacturer
Winbond Electronics Corp America
Datasheet
1.W9425G6JH.pdf
(52 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
w9425g6jh-4
Manufacturer:
PANASONIC
Quantity:
500 000
Part Number:
w9425g6jh-4
Manufacturer:
WINBOND/华邦
Quantity:
20 000
Company:
Part Number:
w9425g6jh-5
Manufacturer:
INFINEON
Quantity:
763
Company:
Part Number:
w9425g6jh-5
Manufacturer:
WINBOND
Quantity:
5 800
Company:
Part Number:
w9425g6jh-5
Manufacturer:
WINBOND
Quantity:
6 990
Company:
Part Number:
w9425g6jh-5
Manufacturer:
WINBOND
Quantity:
2 890
Part Number:
w9425g6jh-5
Manufacturer:
WINBOND/华邦
Quantity:
20 000
e. The ratio of pullup slew rate to pulldown slew rate is specified for the same temperature and
f. Verified under typical conditions for qualification purposes.
g. TSOP II package devices only.
h. Only intended for operation up to 266 Mbps per pin.
i. A derating factor will be used to increase t
j. A derating factor will be used to increase t
k. Table 3 is used to increase t
m. DQS, DM, and DQ input slew rate is specified to prevent double clocking of data and preserve
voltage, over the entire temperature and voltage range. For a given output, it represents the
maximum difference between pullup and pulldown drivers due to process variation.
0.5 V/nS as shown in Table 2. The Input slew rate is based on the lesser of the slew rates
determined by either V
rates differ, as shown in Tables 3 & 4. Input slew rate is based on the larger of AC-AC delta rise,
fall rate and DC-DC delta rise, fall rate. Input slew rate is based on the lesser of the slew rates
determined by either V
The delta rise/fall rate is calculated as:
{1/(Slew Rate1)}-{1/(slew Rate2)}
For example: If Slew Rate 1 is 0.5 V/nS and Slew Rate 2 is 0.4 V/nS, then the delta rise, fall rate is
-0.5 nS/V. Using the table given, this would result in the need for an increase in t
pS.
I/O slew rate is based on the lesser of the AC-AC slew rate and the DC-DC slew rate. The input
slew rate is based on the lesser of the slew rates determined by either V
to V
setup and hold times. Signal transitions through the DC region must be monotonic.
IL(DC)
, and similarly for rising transitions.
IH(AC)
IH(AC)
DS
to V
to V
and t
IL(AC)
IL(AC)
DH
or V
or V
in the case where the I/O slew rate is below 0.5 V/nS. The
IS
IH(DC)
DS
IH(DC)
and t
and t
- 33 -
to V
to V
IH
DH
in the case where the input slew rate is below
IL(DC)
IL(DC)
in the case where DQ, DM, and DQS slew
, similarly for rising transitions.
, similarly for rising transitions.
Publication Release Date: May 26, 2010
IH(AC)
W9425G6JH
to V
DS
IL(AC)
and t
Revision A01
or V
DH
of 100
IH(DC)