hip4080ip Intersil Corporation, hip4080ip Datasheet
hip4080ip
Related parts for hip4080ip
hip4080ip Summary of contents
Page 1
... See also, Application Note AN9324 for the HIP4080. Similar part, HIP4080A, includes under voltage circuitry which doesn’t require the circuitry shown in Figure 30 of this data sheet. Ordering Information PART NUMBER HIP4080IP HIP4080IB HIP4080 (PDIP, SOIC) TOP VIEW 1 20 BHO BHB ...
Page 2
Application Block Diagram 12V HEN DIS HIP4080 IN+ IN- GND Functional Block Diagram CHARGE PUMP HEN DIS 3 5 OUT 6 IN HDEL 9 LDEL HIP4080 80V ...
Page 3
Typical Application (Hysteresis Mode Switching) 1 BHB 12V 2 HEN DIS 3 DIS OUT HDEL LDEL 9 AHB 10 GND HIP4080 20 BHO 19 BHS 18 BLO 17 BLS ...
Page 4
Absolute Maximum Ratings Supply Voltage, V and -0.3V to 16V DD CC Logic I/O Voltages . . . . . ...
Page 5
Electrical Specifications and T A PARAMETERS SYMBOL Low Level Input Current High Level Input Current INPUT PINS: HEN Low Level Input Voltage High Level Input Voltage Input Voltage Hysteresis Low Level Input Current High Level Input ...
Page 6
Pin Descriptions PIN NUMBER SYMBOL 1 BHB B High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of boot- strap diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30 A out ...
Page 7
Timing Diagrams T T HPHL DIS = 0 HEN = 1 IN+ > IN- ALO AHO BLO BHO T LPHL T T HEN-PHL DIS = 0 HEN IN+ > IN- ALO AHO BLO BHO T DLPLH T REF-PW DIS HEN ...
Page 8
Typical Performance Curves 14.0 12.0 10.0 8.0 6.0 4.0 2 SUPPLY VOLTAGE (V) DD FIGURE 4. QUIESCENT I SUPPLY CURRENT SUPPLY VOLTAGE 30.0 25.0 20.0 15.0 10.0 5.0 0.0 0 100 200 300 ...
Page 9
Typical Performance Curves -90 -100 -110 -120 -50 - JUNCTION TEMPERATURE ( FIGURE 10. DIS LOW LEVEL INPUT CURRENT I TEMPERATURE 15.0 14.0 13.0 12.0 11.0 10.0 -40 - JUNCTION TEMPERATURE ( FIGURE ...
Page 10
Typical Performance Curves 375 325 275 225 175 -40 - JUNCTION TEMPERATURE ( FIGURE 16. T REFRESH PULSE WIDTH vs REF-PW TEMPERATURE 90.0 80.0 70.0 60.0 50.0 40.0 -40 - JUNCTION TEMPERATURE ...
Page 11
Typical Performance Curves 13.5 12.5 11.5 10.5 9.5 8.5 -40 - JUNCTION TEMPERATURE ( FIGURE 22. GATE DRIVE FALL TIME T 6.0 5.5 5.0 4.5 4.0 -40 - JUNCTION TEMPERATURE ( FIGURE 24. ...
Page 12
Typical Performance Curves 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 AHB FIGURE 28. PEAK PULLUP CURRENT I VOLTAGE 1000 500 200 100 50 20 ...
Page 13
HIP4080 Power-up Application Information The HIP4080 H-Bridge Driver IC requires external circuitry to assure reliable start-up conditions of the upper drivers. If not addressed in the application, the H-Bridge power MOS- FETs may be exposed to shoot-through current, possibly leading ...
Page 14
IN2 IN1 +12V CONTROL LOGIC SECTION R29 JMPR1 1 2 OUT/BLI U2 CD4069UB JMPR2 12 IN+/ALI 13 U2 CD4069UB JMPR3 5 6 HEN/BHI U2 CD4069UB R33 3 JMPR4 11 10 IN-/AHI CD4069UB ...
Page 15
GND +12V CR2 + + C4 R22 U1 BHO R24 DIS BLO U2 BLS IN1 JMPR1 I JMPR2 O ALS JMPR3 R23 ALO IN2 JMPR4 R21 AHO O LDEL C3 ALS CR1 R33 R34 BLS FIGURE 35. HIP4080 EVALUATION BOARD ...
Page 16
Supplemental Information for HIP4080 and HIP4081 Power-Up Application The HIP4080 and HIP4081 H-Bridge Driver ICs require external circuitry to assure reliable start-up conditions of the upper drivers. If not addressed in the application, the H-bridge power MOSFETs may be exposed ...
Page 17
Timing Diagrams V xxxxx DD 12V, FINAL VALUE xxxxx xxxxx 8.5V TO 10.5V (ASSUMES 5% RESISTORS) xxxxx ALI, BLI DIS xxxxx xxxxx xxxxx 1.7V xxxxx NOTE: 7. ALI and/or BLI may be high after t1, whereupon the ENABLE pin may ...
Page 18
Small Outline Plastic Packages (SOIC INDEX xx 0.25(0.010) H AREA - SEATING PLANE - - 0.10(0.004) 0.25(0.010 ...
Page 19
... All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use ...