HI1-574ATD/883 INTERSIL [Intersil Corporation], HI1-574ATD/883 Datasheet
HI1-574ATD/883
Available stocks
Related parts for HI1-574ATD/883
HI1-574ATD/883 Summary of contents
Page 1
TM Complete, 12-Bit A/D Converters with Microprocessor Interface The HI-X74( complete 12-bit, Analog-to-Digital Converter, including a +10V reference clock, three-state outputs and a digital interface for microprocessor control. Successive approximation conversion is performed by two monolithic dice housed ...
Page 2
... Ordering Information PART NUMBER HI3-574AJN-5 HI3-574AKN-5 HI1-574AJD-5 HI1-574AKD-5 HI1-574ASD-2 HI1-574ATD-2 HI1-574ASD/883 HI1-574ATD/883 HI3-674AJN-5 HI3-674AKN-5 HI1-674AJD-5 HI1-674AKD-5 HI1-674ASD-2 HI1-674ATD/883 Functional Block Diagram 12/8 CS CONTROL A O LOGIC R/C CE OSCILLATOR DIGITAL CHIP ANALOG CHIP V IN REF V OUT REF +10V REF ANALOG COMMON NOTE: “Nibble” 4-bit digital word. ...
Page 3
... REFOUT . . . . . Indefinite Short To Common, Momentary Short To V Operating Conditions Temperature Range HI3-574Axx-5, HI1-674Axx HI1-574AxD-2, HI1-674AxD -55 CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. ...
Page 4
DC and Transfer Accuracy Specifications PARAMETER Power Supply Rejection Max Change In Full Scale Calibration +13.5V < V < +16.5V or +11.4V < +4.5V < V < +5.5V LOGIC -16.5V < V < -13.5V or -12.6V < V ...
Page 5
DC and Transfer Accuracy Specifications Unless Otherwise Specified (Continued) PARAMETER Linearity Error - 125 C (Max) Max Resolution For Which No Missing Codes Is Guaranteed MIN MAX ...
Page 6
DC and Transfer Accuracy Specifications Unless Otherwise Specified (Continued) PARAMETER Operating Current I LOGIC I +15V Supply CC I -15V Supply EE Power Dissipation 15V, +5V 12V, +5V Internal Reference Voltage MIN MAX Output current, available for ...
Page 7
Timing Specifications (HI-574A) 25 SYMBOL READ MODE t Access Time from Data Valid After CE Low HD t Output Float Delay Setup SSR t R Setup SRR ...
Page 8
Pin Descriptions PIN SYMBOL DESCRIPTION 1 V Logic supply pin (+5V) LOGIC 2 12/8 Data Mode Select - Selects between 12- bit and 8-bit output modes Chip Select - Chip Select high disables the device Byte ...
Page 9
C) value to the value MAX Power Supply Rejection The standard specifications for the HI-X74A assume use of +5.00V and 15.00V or 12.00V supplies. The only effect of power supply ...
Page 10
These will require an additional wideband buffer amplifier to lower their output impedance. A simpler solution is to use the Intersil HA-5320 Sample/Hold, which was designed for use with the HI-574A OFFSET 5 ...
Page 11
Connect the Analog signal to pin 13 for a 5V range pin 14 for a 10V range. Calibration of offset and gain is similar to that for the unipolar ranges as discussed above. 1 First apply a DC ...
Page 12
See the HI-X74A Timing Specifications, Convert Mode. This variety of HI-X74A control modes allows a simple interface in most system ...
Page 13
INPUT BUFFERS 12 R/C CE EOC9 LATCH O EOC13 13 A ADDRESS BUS STS 2 12/8 DB11 (MSB ...
Page 14
HRL R STS t HDR DATA DB11-DB0 VALID FIGURE 7. LOW PULSE FOR R/C - OUTPUTS ENABLED AFTER CONVERSION R/C t HRH STS t HDR t DDR HIGH-Z DB11-DB0 DATA VALID FIGURE 8. HIGH PULSE FOR R/C ...
Page 15
Die Characteristics DIE DIMENSIONS: Analog: 3070mm x 4610mm Digital: 1900mm x 4510mm METALLIZATION: Digital Type: Nitrox Å Å Thickness: 10k 2k Metal 1: AlSiCu Å Å Thickness Metal 2: AlSiCu Å Å Thickness: 16k 2k Analog Type: Al ...
Page 16
Ceramic Dual-In-Line Metal Seal Packages (SBDIP) -A- -D- E -B- bbb BASE S2 PLANE -C- SEATING PLANE ccc ...
Page 17
Dual-In-Line Plastic Packages (PDIP INDEX N/2 AREA -B- -A- D BASE PLANE -C- SEATING PLANE 0.010 (0.25 NOTES: 1. Controlling Dimensions: INCH. In case of conflict between ...