Single, Double or Triple-Output Hot Plug
Controller
The HIP1020 applies a linear voltage ramp to the gates of
any combination of 3.3V, 5V, and 12V MOSFETs. The
internal charge pump doubles a 12V bias or triples a 5V bias
to deliver the high-side drive capability required when using
more cost-effective N-Channel MOSFETs. The 5V/ms ramp
rate is controlled internally and is the proper value to turn on
most devices within the Device-Bay-specified di/dt limit. If a
slower rate is required, the internally-determined ramp rate
can be over ridden using an optional external capacitor.
When VCC = 12V, the charge pump ramps the voltage on
HGATE from zero to 22V in about 4ms. This allows either a
standard or a logic-level MOSFET to become fully enhanced
when used as a high-side switch for 12V power control. The
voltage on LGATE ramps from zero to 16V allowing the
simultaneous control of 3.3V and/or 5V MOSFETs.
When VCC = 5V, the charge pump enters voltage-tripler
mode. The voltage on HGATE ramps from zero to 12.5V in
about 3ms while LGATE ramps to 12.0V. This mode is ideal
for control of high-side MOSFET switches used in 3.3V and
5V power switching when 12V bias is not available.
Ordering Information
NOTE: Intersil Pb-free products employ special Pb-free material sets; molding
compounds/die attach materials and 100% matte tin plate termination finish,
which is compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J Std-020B.
Typical Applications
HIP1020CK-T
HIP1020CKZ-T
(See Note)
FIGURE 1A. DEVICE-BAY HOT PLUG CONTROLLER WITH
V
V
NUMBER
V
12
33
5
PART
VCC = 12V
1
2
3
RANGE (
0 to 70
0 to 70
TEMP.
CHARGE
PUMP
HIP1020
®
o
1
C)
5 Ld SOT23 T + R P5.064
5 Ld SOT23 T + R
(Pb-free)
Data Sheet
5
4
PACKAGE
ENABLE
OPTIONAL
C1
V
V
V
12,OUT
5,OUT
33,OUT
P5.064
DWG. #
PKG.
1-888-INTERSIL or 321-724-7143
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
Features
• Rise Time Controlled to Device-Bay Specifications
• No Additional Components Required
• Internal Charge Pump Drives N-Channel MOSFETs
• Drives any Combination of One, Two or Three Outputs
• Internally-Controlled Turn-On Ramp
• Prevents False Turn on During Hot Insertion
• Operates using 12V or 5V Bias
• Improves Device Bay Peripheral Size Cost and Complexity
• Controls Standard and Logic-Level MOSFETs
• Compatible with TTL and 3.3V Logic Devices
• Shutdown Current . . . . . . . . . . . . . . . . . . . . . . . . . . < 1µA
• Operating Current . . . . . . . . . . . . . . . . . . . . . . . . . .< 3mA
Applications
• Device Bay Peripherals
• Hot Plug Control
• Power Distribution Control
Pinout
FIGURE 1B. DEVICE-BAY HOT PLUG CONTROLLER WITH
- Optional Capacitor Selects Slower Rates
- Minimal Component Count
- Tiny 5-Pin SOT23 Package
V
V
33
5
All other trademarks mentioned are the property of their respective owners.
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
VCC = 5V
Copyright © Intersil Americas Inc. 1999, 2004. All Rights Reserved
LGATE
July 2004
GND
VCC
1
2
3
1
2
3
HIP1020 (SOT23)
CHARGE
TOP VIEW
PUMP
HIP1020
5
4
4
5
ENABLE
EN
HGATE
OPTIONAL
HIP1020
C1
FN4601.2
V
V
5,OUT
33,OUT