HC5517 Intersil Corporation, HC5517 Datasheet - Page 2

• Manufacturer Part Number: HC5517
• Description: 3 REN Ringing SLIC For ISDN Modem/TA and WLL
• Manufacturer: Intersil Corporation

Absolute Maximum Ratings
Maximum Supply Voltages
Relay Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +15V
Operating Conditions
Operating Temperature Range
Relay Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V to +12V
Positive Power Supply (V
Negative Power Supply (V
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
Electrical Specifications
RINGING TRANSMISSION PARAMETERS
V
4-Wire to 2-Wire Gain
AC TRANSMISSION PARAMETERS
RX Input Impedance
TX Output Impedance
4-Wire Input Overload Level
2-Wire Return Loss
2-Wire Longitudinal to Metallic Balance
Off Hook
4-Wire Longitudinal Balance Off Hook
Low Frequency Longitudinal Balance
Longitudinal Current Capability
Insertion Loss
1.
2. All grounds (AGND, BGND) must be applied before V
(V
(V
HC5517IM, HC5517IB . . . . . . . . . . . . . . . . . . . . . . -40
HC5517CM, HC5517CB . . . . . . . . . . . . . . . . . . . . . . 0
RING
SRL LO
ERL
SRL HI
2-Wire/4-Wire (Includes external transhybrid
amplifier with a gain of 3)
4-Wire/2-Wire
4-Wire/4-Wire (Includes external transhybrid
amplifier with a gain of 3)
CC
CC
to run separate grounds off a line card, the AG must be applied first.
JA
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7V
)-(V
Input Impedance
is measured with the component mounted on an evaluation PC board in free air.
BAT
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90V
PARAMETER
CC
BAT
) . . . . . . . . . . . . . . . . . . . . . . . +5V 5%
) . . . . . . . . . . . . . . . . . . .-16V to -80V
61
Unless Otherwise Specified, Typical Parameters are at T
Operating Temperature Range, V
at 600 2-Wire terminating impedance.
T
A
= 25
o
C
(Note 3)
V
300Hz to 3.4kHz (Note 3)
300Hz to 3.4kHz (Note 3)
300Hz to 3.4kHz R
(Note 3)
Matched for 600 (Note 3)
Per ANSI/IEEE STD 455-1976 (Note 3)
300Hz to 3400Hz
300Hz to 3400Hz (Note 3)
I
I
0dBm at 1kHz, Referenced 600
LINE
LINE
RING
o
o
C to 85
C to 75
CC
= 40mA T
= 40mA T
to Vt-r (Note 3)
or V
o
o
BAT
C
C
HC5517
TEST CONDITIONS
A
A
BAT
. Failure to do so may result in premature failure of the part. If a user wishes
= 25
= 25
L
= -24V, V
= 1200 , 600 Reference
o
o
C (Note 3)
C (Note 3)
Thermal Information
Thermal Resistance (Typical, Note 1)
Maximum Junction Temperature Plastic . . . . . . . . . . . . . . . . .150
Maximum Storage Temperature Range . . . . . . . . . . -65
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300
Die Characteristics
Transistor Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Diode Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Die Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 x 120
Substrate Potential. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .V
Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bipolar-DI
ESD (Human Body Model) . . . . . . . . . . . . . . . . . . . . . . . . . . . .500V
PLCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(SOIC, PLCC - Lead Tips Only)
CC
= +5V, AGND = BGND = 0V. All AC Parameters are specified
A
= 25
o
C, Min-Max Parameters are over
+1.0
MIN
26
30
30
58
50
-
-
-
-
-
-
-
-
-
TYP
108
5.4
0.05
0.05
40
35
40
40
63
55
10
-
-
-
-
MAX
0.25
20
23
40
0.2
0.2
-
-
-
-
-
-
-
-
-
o
C to 150
JA
mA
UNITS
V
dBrnC
(
55
70
V/V
PEAK
o
k
k
dB
dB
dB
dB
dB
dB
dB
dB
RMS
C/W)
BAT
o
o
o
C
C
C