IS46TR16128A-15HBLA2 ISSI, IS46TR16128A-15HBLA2 Datasheet - Page 69

• Manufacturer Part Number: IS46TR16128A-15HBLA2
• Description: DRAM 2G, 1.5v, 1333MT/s 128Mx16 DDR3
• Manufacturer: ISSI

Specifications of IS46TR16128A-15HBLA2

• Rohs: yes
• Data Bus Width: 16 bit
• Organization: 128 M x 16
• Package / Case: FBGA-96
• Memory Size: 2 Gbit
• Maximum Clock Frequency: 933 MHz
• Access Time: 13.125 ns
• Supply Voltage - Max: 1.575 V
• Supply Voltage - Min: 1.425 V
• Maximum Operating Current: 65 mA
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT

IS43/46TR16128A, IS43/46TR16128AL,
IS43/46TR82560A, IS43/46TR82560AL
Specific Note f
When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(mper), act of
the input clock, where 2 <= m <=12. (output derating are relative to the SDRAM input clock.)
For example, if the measured jitter into a DDR3-800 SDRAM has tERR(mper),act,min = -172ps and tERR(mper),act,max
= 193ps, then tDQSCK,min(derated) = tDQSCK,min - tERR(mper),act,max = -400ps - 193ps = -593ps and
tDQSCK,max(derated) = tDQSCK,max - ERR(mper),act,min = 400ps + 172ps = 572ps. Similarly, tLZ(DQ) for DDR3-800
derates to tLZ(DQ),min(derated) = -800ps - 193ps = -993ps and tLZ(DQ),max(derated) = 400ps + 172ps = 572ps.
(Caution on the min/max usage!)
Note that tERR(mper),act,min is the minimum measured value of tERR(nper) where 2 <= n <= 12, and
tERR(mper),act,max is the maximum measured value of tERR(nper) where 2 <= n <= 12.
Specific Note g
When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT(per),act of the
input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR3-800
SDRAM has tCK(avg),act=2500ps, tJIT(per),act,min = -72ps and tJIT(per),act,max = 93ps, then tRPRE,min(derated) =
tRPRE,min + tJIT(per),act,min = 0.9 x tCK(avg),act + tJIT(per),act,min = 0.9 x 2500ps - 72ps = 2178ps. Similarly,
tQH,min(derated) = tQH,min + tJIT(per),act,min = 0.38 x tCK(avg),act + tJIT(per),act,min = 0.38 x 2500ps - 72ps = 878ps.
(Caution on the min/max usage!)
9.4 Timing Parameter Notes
1. Actual value dependent upon measurement level definitions.
2. Commands requiring a locked DLL are: READ ( and RAP) are synchronous ODT commands.
3. The max values are system dependent.
4. WR as programmed in mode register.
5. Value must be rouned-up to next higher integer value.
6. There is no maximum cycle time limit besides the need to satisfy the refresh interval, tREFI.
7. For definition of RTT-on time tAON See “Timing Parameters”.
8. For definition of RTT-off time tAOF See “Timing Parameters”.
9. tWR is defined in ns, for calculation of tWRPDEN it is necessary to round up tWR / tCK to the next integer.
10. WR in clock cycles are programmed in MR0.
11. The maximum read postamble is bonded by tDQSCK(min) plus tQSH(min) on the left side and tHZ(DQS)max on the
12. Output timing deratings are relative to the SDRAM input clock. When the device is operated with input clock jitter, this
13. Value is only valid for RON34.
14. Single ended signal parameter.
15. tREFI depends on TOPER.
16. tIS(base) and tIH(base) values are for 1V/ns CMD/ADD single-ended slew rate and 2V/ns CK, CK differential slew
17. tDS(base) and tDH(base) values are for 1V/ns DQ single-ended slew rate and 2V/ns DQS, DQS differential slew rate.
18. Note for DQ and DM signals, VREF(DC)=VRefDQ(DC). For input only pins except RESET, VRef(DC)=VRefCA(DC).
19. Start of internal write transaction is defined as follows:
20. For BL8 (fixed by MRS and on-the-fly): Rising clock edge 4 clock cycles after WL.
21. For BC4 (on-the-fly): Rising clock edge 4 clock cycles after WL.
22. For BC4 (fixed by MRS): Rising clock edge 2 clock cycles after WL.
19. The maximum preamble is bound by tLZ(DQS)max on the left side and tDQSCK(max) on the right side.
20. CKE is allowed to be registered low while operations such as row activation, precharge, autoprecharge or refresh are
21. Although CKE is allowed to be registered LOW after a REFRESH command once tREFPDEN(min) is satisfied, there
22. Defined between end of MPR read burst and MRS which reloads MPR or disables MPR function.
Integrated Silicon Solution, Inc. – www.issi.com –
Rev. 00A
11/14/2012
right side.
parameter needs to be derated by TBD.
rate. Note for DQ and DM signals, VREF(DC)=VRefDQ(DC). For input only pins except RESET,
VRef(DC)=VRefCA(DC).
in progress, but power-down IDD spec will not be applied until finishing those operations.
are cases where additional time such as tXPDLL(min) is also required.
69