ISL267817IBZ-T Intersil, ISL267817IBZ-T Datasheet
ISL267817IBZ-T
Specifications of ISL267817IBZ-T
Related parts for ISL267817IBZ-T
ISL267817IBZ-T Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. 512 1024 1536 2048 2560 3072 3584 4096 ...
Page 2
... GND 4 5 Ordering Information PART NUMBER (Notes ISL267817IBZ 267817 IBZ ISL267817IUZ 67817 NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations) ...
Page 3
Table of Contents Typical Connection Diagram ...
Page 4
... Thermal Resistance (Typical SOIC Package (Notes 4, 5 MSOP Package (Notes 4, 5 Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp = 3.2MHz 200kSPS 2.5V; V DCLOCK S REF TEST CONDITIONS +IN – ...
Page 5
Electrical Specifications +VCC = +5V, f Boldface limits apply over the operating temperature range, -40°C to +85°C. (Continued) SYMBOL PARAMETER REFERENCE INPUT VREF VREF Input Range VREFLEAK Current Drain DIGITAL INPUT/OUTPUT Logic Family V Input High Voltage IH V Input ...
Page 6
Timing Specifications Limits established by characterization and are not production tested. +VCC = 5V 2.5V Boldface limits apply over the operating temperature range, -40°C to +85°C. (Continued) REF CM REF SYMBOL PARAMETER t ...
Page 7
DCLOCK t EN DOUT VOL = 0.4V VIH = 2.4V CS/SHDN t DIS DOUT 10% FIGURE 5. TIMING PARAMETER DEFINITIONS 7 ISL267817 VIL = 0.8V DCLOCK t hDO DOUT VOH = VDD - 0.2V VIL = 0.8V DCLOCK t ...
Page 8
Typical Performance Characteristics unless otherwise specified. CLK SAMPLE 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 -1.0 -1.5 -2.0 -2.5 1.00 1.20 1.40 1.60 1.80 REFERENCE VOLTAGE (V) FIGURE 6. CHANGE IN OFFSET vs REFERENCE ...
Page 9
Typical Performance Characteristics unless otherwise specified. (Continued) CLK SAMPLE 0 -20 -40 -60 -80 -100 -120 FREQUENCY (kHz) FIGURE 12. FREQUENCY SPECTRUM (8192 POINT FFT 9.9kHz, –0.5dB IN 95 ...
Page 10
Typical Performance Characteristics unless otherwise specified. (Continued) CLK SAMPLE 1.00 0.75 0.50 0.25 0.00 -0.25 -0.50 -0.75 -1.00 0 512 1024 1536 2048 2560 3072 3584 4096 FIGURE 18. DIFFERENTIAL LINEARITY ERROR vs CODE ...
Page 11
Typical Performance Characteristics unless otherwise specified. (Continued) CLK SAMPLE FIGURE 24. REFERENCE CURRENT vs TEMPERATURE (CODE = FF8h) Functional Description The ISL267817 is based on a successive approximation register (SAR) architecture utilizing capacitive charge ...
Page 12
Differential signaling offers several benefits over a single-ended input, such as: • Doubling of the full-scale input range (and therefore the dynamic range) • Improved even order harmonic distortion • Better noise immunity due to common mode rejection Figure 28 ...
Page 13
BULK + 0.1µF +5V VIN VOUT POWER-DOWN/STANDBY MODES The mode of operation of the ISL267817 is selected by controlling the logic state of the CS/SHDN signal during a conversion. There are two possible modes of operation: dynamic mode or ...
Page 14
ADC is roughly constant, decreasing somewhat at lower throughput rates (Figure 35). The shutdown current is impacted by the state of the CS/SHDN pin, as shown in Figure 36. 1000 T ...
Page 15
V is the RMS amplitude of the fundamental and and V are the RMS amplitudes of the second to the sixth harmonics. Peak Harmonic or Spurious Noise (SFDR) Peak harmonic ...
Page 16
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. ...
Page 17
Package Outline Drawing M8.15 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 4, 1/12 INDEX AREA TOP VIEW 5.00 (0.197) 4.80 (0.189) 1.27 (0.050) 0.51(0.020) 0.33(0.013) SIDE VIEW “A 17 ISL267817 DETAIL "A" 6.20 (0.244) 5.80 ...
Page 18
Package Outline Drawing M8.118 8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE Rev 4, 7/11 3.0±0. PIN TOP VIEW H 0.25 - 0.36 0. A-B D SIDE VIEW 1 (5.80) (4.40) (3.00) ...