STM32L151RBH6TR STMicroelectronics, STM32L151RBH6TR Datasheet - Page 49

• Manufacturer Part Number: STM32L151RBH6TR
• Description: ARM Microcontrollers - MCU 32-Bit ARM Cortex 128kb Low Power MCU
• Manufacturer: STMicroelectronics

Specifications of STM32L151RBH6TR

• Product Category: ARM Microcontrollers - MCU
• Rohs: yes
• Core: ARM Cortex M3
• Data Bus Width: 32 bit

STM32L151x6/8/B, STM32L152x6/8/B
6.2
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 12: Current
permanent damage to the device. These are stress ratings only and functional operation of
the device at these conditions is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
Table 11.
1. All main power (V
2.
Table 12.
1. All main power (V
2. Negative injection disturbs the analog performance of the device. See note in
3. Positive current injection is not possible on these I/Os. A negative injection is induced by V
4. A positive injection is induced by V
5. When several inputs are submitted to a current injection, the maximum ΣI
|V
V
V
supply, in the permitted range.
supply, in the permitted range.
must never be exceeded. Refer to
must never be exceeded. Refer to
values.
positive and negative injected currents (instantaneous values).
Symbol
SSX
I
V
|ΔV
ESD(HBM)
INJ(PIN)
ΣI
DD
Symbol
V
IN
INJ(PIN)
IN
I
I
–V
VDD
DDx
maximum must always be respected. Refer to
VSS
I
− V
IO
(2)
SS
|
SS
(2)
|
Voltage characteristics
Current characteristics
External main supply voltage
(including V
Input voltage on five-volt tolerant pin
Input voltage on any other pin
Variations between different V
Variations between all different ground pins
Electrostatic discharge voltage
(human body model)
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current sourced by any I/O and control pin
Injected current on five-volt tolerant I/O
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DD
DD
characteristics, and
, V
, V
DDA
DDA
) and ground (V
) and ground (V
DDA
and V
Doc ID 17659 Rev 8
Table 11: Voltage characteristics
Table 11
IN
Ratings
> V
DD
DD
SS
DD
/V
)
SS
SS
(1)
DDA
Table 13: Thermal characteristics
ground lines (sink)
while a negative injection is induced by V
for maximum allowed input voltage values.
, V
, V
Ratings
SSA
SSA
power lines (source)
DD
Table 12
) pins must always be connected to the external power
) pins must always be connected to the external power
power pins
(4)
for maximum allowed injected current values.
(3)
(1)
Table 11: Voltage
for the maximum allowed input voltage
see
(1)
V
V
INJ(PIN)
SS
SS
Section 6.3.10
–0.3
Min
(5)
Electrical characteristics
− 0.3
− 0.3
Section
is the absolute sum of the
IN
may cause
6.3.16.
< V
characteristics,
V
+0 /-5
IN
Max.
± 25
- 25
± 5
SS
DD
80
80
25
Max
<V
4.0
4.0
50
50
. I
+4.0
SS
INJ(PIN)
. I
INJ(PIN)
Unit
49/121
mA
Unit
mV
V