ISL55210-ABEVAL1Z Intersil, ISL55210-ABEVAL1Z Datasheet
ISL55210-ABEVAL1Z
Specifications of ISL55210-ABEVAL1Z
Related parts for ISL55210-ABEVAL1Z
ISL55210-ABEVAL1Z Summary of contents
Page 1
... Designer's Guide to the ISL55210-ABEVAL1Z Active Balun Evaluation Board Using the Active Balun Board to Test Design Options This relatively simple board is intended to provide a quick means to test the performance of the active balun configuration using the ISL55210. While all wideband, voltage feedback (VFA), fully differential amplifiers (FDA) can perform ...
Page 2
... The 16.4dB gain used as the setting for the active balun evaluation board simulates very flat through 1GHz with approximately 4GHz F-3dB bandwidth for the response to the ISL55210 outputs. In fact the board shows a response shape set by the blocking capacitors on the low end and the output 24dB transformer on the high end ...
Page 3
... The supply decoupling and Vcm decoupling is the same used as for the standard ISL55210 evaluation board except R12 is reduced from 200Ω to 20Ω to reduce noise into the Vcm reference path. The optional elements (green) not populated in the board as delivered include: 1. Two capacitors on the inverting summing junctions (C5 and C6) ...
Page 4
... The high frequency rolloff follows the simulation of Figure 3 up through about 600MHz then a slight peaking in the ISL55210 response is pulling it back up. This is showing a 10.2dB midband gain to a matched load (the two series output resistors set the output impedance since the ISL55210 is a broadband low impedance output itself) with ≤ ...
Page 5
... The Noise Figure (NF) in this relatively low gain setting calculates to approximately 7dB. This low NF is depending on the low 0.85nV/√Hz differential input spot noise for the ISL55210 and the reduced resistor values enabled by this active input match capability. Going to higher gain settings will reduce the input NF where for gains > ...
Page 6
... FIGURE 10. MEASURED AND LINE FIT OIP3 FOR THE CIRCUIT OF FIGURE 1 DRIVING A DOUBLY TERMINATED 50Ω LOAD The ISL55210 does show true intercept performance on the 3rd order terms and Figure 10 is showing the expected rolloff in the intercept for this low power device as the loop gain rolls off. ...
Page 7
... References [1] These simulations are in the free Intersil Spice and power simulation package available as a download at http://www.intersil.com/content/intersil/en/tools/isim.ht ml [2] These are presented part EDN article where Part 1 is here. http://www.edn.com/design/analog/4410567/Wideband- matched-input-impedance-with-ultra-low-noise-using-the- active-match-capability-of-a-new-type-of-amplifier--part-1-of- 2-- [3] This plot actually comes from an article using this active balun stage with a bandwidth extension technique for the ADT1-1WT ...
Page 8
... ISL55210-ABEVAL1Z Bill of Materials PART NUMBER QTY UNITS ISL55210-ABEVAL1ZREVAPCB 1 ea 100X14W104MV4T C8, C11 C1608C0G1H103J C1, C2, C3, C4, C3a, C4a, C3b, C4b CAP, SMD, 0603, 0.01µF, 50V, 5%, C0G/NP0, H1044-DNP 0 ea C5, C6 H1045-00104-50V10 C7, C9, C10, C14 H1065-00105-50V10 C12 H1121-00475-10V10-B C13 108-0740-001 ...
Page 9
... ISL55210-ABEVAL1Z Bill of Materials PART NUMBER QTY UNITS H2511-049R9-1/10W1 R6b, R7b H2511-061R9-1/10W1 H2511-084R5-1/10W1 R6a, R7a H2511-DNP 0 ea R1b, R2b, RJ1a, RJ2a ADT1-1WT ADT1-1WT MABA-007871-CT1A40 5X8-STATIC-BAG 1 ea Place assy in bag LABEL-DATE CODE 1 ea AFFIX TO BACK OF PCB Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice ...