PCA9633D16,112 NXP Semiconductors, PCA9633D16,112 Datasheet - Page 15

• Manufacturer Part Number: PCA9633D16,112
• Description: IC LED DRIVER RGBA 16-SOIC
• Manufacturer: NXP Semiconductors
• Type: RGBA LED Driverr

Specifications of PCA9633D16,112

• Package / Case: 16-SOIC (3.9mm Width)
• Topology: Open Drain, PWM
• Number Of Outputs: 4
• Internal Driver: Yes
• Type - Primary: Backlight, LED Blinker
• Type - Secondary: RGBA
• Frequency: 1MHz
• Voltage - Supply: 2.3 V ~ 5.5 V
• Voltage - Output: 5.5V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 25mA
• Internal Switch(s): Yes
• Low Level Output Current: 17 mA
• High Level Output Current: 50 uA
• Operating Supply Voltage: 2.3 V to 5.5 V
• Maximum Supply Current: 100 mA
• Maximum Power Dissipation: 400 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Number Of Segments: 8
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Package Type: SO
• Pin Count: 16
• Mounting: Surface Mount
• Power Dissipation: 400mW
• Operating Supply Voltage (min): 2.3V
• Operating Supply Voltage (max): 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: OM6282 - DAUGHTER CARD PCA9633 FOR OM6275OM6276,598 - DEMO BOARD PWM LED622-1004 - BOARD DEMO FOR PHILIPS PCA9633
• Efficiency: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-3235-5; 935281309112; PCA9633D16

NXP Semiconductors
PCA9633_5
Product data sheet
7.3.7 I
7.3.8 LED All Call I
Table 14.
Legend: * default value.
Subaddresses are programmable through the I
E4h, E8h, and the device(s) will not acknowledge these addresses right after power-up
(the corresponding SUBx bit in MODE1 register is equal to 0).
Once subaddresses have been programmed to their right values, SUBx bits need to be
set to 1 in order to have the device acknowledging these addresses (MODE1 register).
Only the 7 MSBs representing the I
register is a read-only bit (0).
When SUBx is set to 1, the corresponding I
an I
Table 15.
Legend: * default value.
The LED All Call I
at the same time (ALLCALL bit in register MODE1 must be equal to 1, power-up default
state). This address is programmable through the I
an I
sub call.
Only the 7 MSBs representing the All Call I
ALLCALLADR register is a Read-only bit (0).
If ALLCALL bit = 0, the device does not acknowledge the address programmed in register
ALLCALLADR.
Address
09h
0Ah
0Bh
Address
0Ch
2
C-bus subaddress 1 to 3, SUBADRx
2
2
C-bus read or write sequence.
C-bus read or write sequence. The register address can be programmed as a
Register
SUBADR1
SUBADR2
SUBADR3
Register
ALLCALLADR
SUBADR1 to SUBADR3 - I
0Bh) bit description
ALLCALLADR - LED All Call I
description
2
C-bus address, ALLCALLADR
2
C-bus address allows all the PCA9633s in the bus to be programmed
Rev. 05 — 25 July 2008
Bit
7:1
0
7:1
0
7:1
0
Bit
7:1
0
Symbol
A1[7:1]
A1[0]
A2[7:1]
A2[0]
A3[7:1]
A3[0]
Symbol
AC[7:1]
AC[0]
2
2
C-bus subaddress are valid. The LSB in SUBADRx
C-bus subaddress registers 0 to 3 (address 09h to
2
C-bus address register (address 0Ch) bit
Access Value
R/W
R only
R/W
R only
R/W
R only
2
2
Access Value
R/W
R only
C-bus address are valid. The LSB in
C-bus subaddress can be used during either
2
C-bus. Default power-up values are E2h,
2
1110 001*
0*
1110 010*
0*
1110 100*
0*
C-bus and can be used during either
1110 000*
0*
4-bit Fm+ I
Description
I
reserved
I
reserved
I
reserved
2
2
2
Description
ALLCALL I
address register
reserved
C-bus subaddress 1
C-bus subaddress 2
C-bus subaddress 3
PCA9633
2
© NXP B.V. 2008. All rights reserved.
C-bus LED driver
2
C-bus
15 of 43