ISL6124IRZA Intersil, ISL6124IRZA Datasheet - Page 11

• Manufacturer Part Number: ISL6124IRZA
• Description: IC POWER SUPPLY SEQUENCER 24QFN
• Manufacturer: Intersil

Specifications of ISL6124IRZA

• Applications: Power Supply Sequencer
• Voltage - Supply: 1.5 V ~ 5.5 V
• Current - Supply: 200µA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-VQFN
• Peak Reflow Compatible (260 C): Yes
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Input: -

Typical Performance Curves
Using the ISL612XSEQEVAL1Z Platform
The ISL612XSEQEVAL1Z platform is the primary evaluation
board for this family. The board has two complete, separate
and electrically identical circuits. See Figure 16 for its
schematic and photograph. Additionally, there is an ISL6125
specific evaluation platform, ISL6125EVAL1Z, due to its
unique open drain outputs for ease of evaluation. See
Figure 17 for its schematic and photograph.
In the top right hand corner of the board is a SMD layout with
ISL6123 illustrating the full functionality and small
implementation size for an application having the highest
component count.
The majority of the board is given over to a socket and
discrete through-hole components circuit for ease of
evaluation flexibility through IC variant swapping and
modification of UVLO levels and sequencing order by
passive component substitution.
The board is shipped with the ISL6123 installed in both
locations and with two each of the other released variant
types loose packed. As this sequencer family has a common
function pinout there are no major modifications to the board
necessary to evaluate the other ICs.
To the left, right and above the socket are four test point
strips (TP1, TP2, TP3, TP4). These give access to the
labeled IC I/O pins during evaluation. Remember that
significant current or capacitive loading of particular I/O pins
will affect functionality and performance.
Attention to orientation and placement of variant ICs in the
socket must be paid to prevent IC damage or faulty
evaluation.
ISL6123, ISL6124, ISL6125, ISL6126, ISL6127, ISL6128, ISL6130
11
FIGURE 7. SYSRST LOW TO OUTPUT LATCH OFF
2V/DIV
SYSRST
(Continued)
3.3VOUT
5VOUT
GATE
The default configuration of the ISL612XSEQEVAL1Z
circuitries was built around the following design
assumptions:
All scope shots are taken from ISL612XSEQEVAL1Z board.
Figures 8 and 9 illustrate the desired turn-on and turn-off
sequences respectively. The sequencing order and delay
1. Using the ISL6123IR or ISL6124IR
2. The four supplies being sequenced are 5V (IN_A), 3.3V
3. The desired order turn-on sequence is first both 5V and
4. The desired turn-off sequence is first both 1.5V and 3.3V
V
(IN_B), 2.5V (IN_C) and 1.5V (IN_D), the UVLO levels
are ~80% of nominal voltages. Resistors chosen such
that the total resistance of each divider is ~10k using
standard value resistors to approximate 80% of
nominal = 0.63V on UVLO input.
Resistor choice is such that I x R2 = 0.633V at the desired
UV (undervoltage) level as the monitored voltage
decreases. Total resistance in the divider is a factor for
the designer to consider for accuracy of UV level and
efficiency vs electrical noise immunity trade-offs.
3.3V supplies together and then the 2.5V supply about
75ms later and lastly, the 1.5V supply about 45ms later.
supplies at the same time then the 2.5V supply about
50ms later and lastly, the 5V supply about 72ms after
that.
MONITORED
R1
R2
1μs/DIV
UVLO
Vmon/0.633mV = R1+R2/R2
when Vmon = desired UV level as
Vmon decreases.
For example, a 5V supply with a
desired UV level at 4V would mean
R1+R2/R2 = 6.319. Ideally, any R1
and R2 combination that met this ratio
would work, but with only standard
value resistors available, small
deviations will occur.
October 15, 2008
FN9005.10