LM96163CISD/NOPB National Semiconductor, LM96163CISD/NOPB Datasheet - Page 28

• Manufacturer Part Number: LM96163CISD/NOPB
• Description: IC TEMP SENSOR DGTL REMOTE 10LLP
• Manufacturer: National Semiconductor
• Series: PowerWise®, TruTherm®r

Specifications of LM96163CISD/NOPB

• Function: Fan Control, Temp Monitor
• Topology: ADC (Sigma Delta), Comparator, Register Bank, Tach
• Sensor Type: External & Internal
• Sensing Temperature: -40°C ~ 85°C, External Sensor
• Output Type: SMBus™
• Output Alarm: Yes
• Output Fan: Yes
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-LLP
• Temperature Sensor Function: Temp Sensor
• Interface Type: Serial (2-Wire)
• Resolution: 10+SignBit
• Package Type: LLP EP
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LM96163CISDTR

www.national.com
Address
03 (09)
47
and ensure MSB and LSB are from the same reading)
03 (09)
Address
Configuration Register
Tachometer Count and Limit Registers
Hex
HEX
Hex
47
46
TACHOMETER COUNT (MSB) and 46
HEX
Read/
Write
CONFIGURATION REGISTER
R/W
R/W
Read/
Write
R
R
R
R
Bits
4:3
7
6
5
2
1
0
Bits
7:0
7:2
1:0
Value
POR
Value
00
POR
0
0
0
0
0
0
N/A
N/A
00
TEDGE1:TEDGE0
[Reserved]
TAC13:TAC6
TCRITOV
PWMDIS
TAC5:TAC0
ALTMSK
FLTQUE
TCHEN
Name
STBY
Name
HEX
TACHOMETER COUNT (LSB) REGISTERS (16 bits: Read LSB first to lock MSB
ALERT Mask
0: ALERT interrupts are enabled.
1: ALERT interrupts are masked, and the ALERT pin is always in a high
impedance (open) state.
Standby
0: the LM96163 is in operational mode, converting, comparing, and updating the
PWM output continuously.
1: the LM96163 enters a low power standby mode.
In standby, continuous conversions are stopped, but a conversion/comparison
cycle may be initiated by writing any value to register 0x0F the One-shot Register.
Operation of the PWM output in standby depends on the setting of bit 5 in this
register.
PWM Disable in Standby
0: the LM96163’s PWM output continues to output the current fan control signal
while in STANDBY.
1: the PWM output is disabled (as defined by the PWM polarity bit) while in
STANDBY.
This bit is unused and always read as 0.
TACH Enable
0: disables the TACH input
1: enables the TACH input
T_CRIT Limit Override
0: locks the T_CRIT limit for the remote diode, POR setting is nominally 110°C
1: unlocks the T_CRIT limit and allows it to be reprogrammed multiple times
RDTS Fault Queue
0: an ALERT will be generated if any Remote Diode conversion result is above
the Remote High Set Point or below the Remote Low Setpoint.
1: an ALERT will be generated only if three consecutive Remote Diode
conversions are above the Remote High Set Point or below the Remote Low
Setpoint.
Tachometer Count (MSB and LSB)
These registers contain the current 16-bit Tachometer Count, representing the
period of time between tach pulses.
Note that the 16-bit tachometer MSB and LSB register addresses are in reverse
order from the 16 bit temperature readings.
Tachometer Edge Programming
Note: If PWM_Clock_Select = 360 kHz, then Tach_Count_Multiple = 1
regardless of the setting of these bits.
Bits
00:
01:
10:
11:
28
Edges Used
2
3
5
Description
Description
Reserved - do not use
Tach_Count_Multiple
4
2
1