ISL6410AIRZ-TK Intersil, ISL6410AIRZ-TK Datasheet - Page 12

• Manufacturer Part Number: ISL6410AIRZ-TK
• Description: IC PWM REG SGL SYNC BUCK 16-QFN
• Manufacturer: Intersil
• Type: Step-Down (Buck), PWM - Current Moder

Specifications of ISL6410AIRZ-TK

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 1.2V, 1.8V, 3.3V
• Current - Output: 600mA
• Frequency - Switching: 750kHz
• Voltage - Input: 3 ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: *
• Package / Case: 16-VQFN Exposed Pad, 16-HVQFN, 16-SQFN, 16-DHVQFN
• Voltage - Supply: 4.5 V ~ 5.5 V
• Frequency-max: 860kHz
• Duty Cycle: 93%
• Pwm Type: Current Mode
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ISL6410AIRZ-TKTR

Quad Flat No-Lead Plastic Package (QFN)
Micro Lead Frame Plastic Package (MLFP)
12
ISL6410, ISL6410A
L16.4x4
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
(COMPLIANT TO JEDEC MO-220-VGGC ISSUE C)
NOTES:
10. Depending on the method of lead termination at the edge of the
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
6. The configuration of the pin #1 identifier is optional, but must be
7. Dimensions D2 and E2 are for the exposed pads which provide
8. Nominal dimensions are provided to assist with PCB Land Pattern
9. Features and dimensions A2, A3, D1, E1, P & θ are present when
SYMBOL
between 0.15mm and 0.30mm from the terminal tip.
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
improved electrical and thermal performance.
Design efforts, see Intersil Technical Brief TB389.
Anvil singulation method is used and not present for saw
singulation.
package, a maximum 0.15mm pull back (L1) maybe present. L
minus L1 to be equal to or greater than 0.3mm.
A1
A2
A3
D1
D2
E1
E2
Nd
Ne
L1
A
D
E
N
P
b
e
k
L
θ
0.80
0.23
1.95
1.95
0.25
0.50
MIN
-
-
-
-
-
MILLIMETERS
NOMINAL
4.00 BSC
3.75 BSC
4.00 BSC
3.75 BSC
0.20 REF
0.65 BSC
0.90
0.28
2.10
2.10
0.60
16
4
4
-
-
-
-
-
-
MAX
1.00
0.05
1.00
0.35
2.25
2.25
0.75
0.15
0.60
12
-
Rev. 5 5/04
NOTES
5, 8
7, 8
7, 8
10
9
9
9
9
8
2
3
3
9
9
-
-
-
-
-
-