HIP6302CB Intersil, HIP6302CB Datasheet - Page 12

• Manufacturer Part Number: HIP6302CB
• Description: IC CTRLR PWM MULTIPHASE 16-SOIC
• Manufacturer: Intersil

Specifications of HIP6302CB

• Pwm Type: Controller
• Number Of Outputs: 2
• Frequency - Max: 305kHz
• Voltage - Supply: 4.75 V ~ 5.25 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 16-SOIC (3.9mm Width)
• Frequency-max: 305kHz
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Duty Cycle: -

With a high dv/dt load transient, typical of high performance
microprocessors, the largest deviations in output voltage
occur at the leading and trailing edges of the load transient. In
order to fully utilize the output-voltage tolerance range, the
output voltage is positioned in the upper half of the range
when the output is unloaded and in the lower half of the range
when the controller is under full load. This droop
compensation allows larger transient voltage deviations and
thus reduces the size and cost of the output filter components.
R
the normal full load current 50µA applied through the R
resistor (or at a different full load current if adjusted as under
“Over-Current, Selecting R
R
For a Vdroop of 80mV, R
The AC feedback components, R
relation to R
Current Balancing
The detected currents are also used to balance the phase
currents.
Each phase’s current is compared to the average of the two
phase currents, and the difference is used to create an offset
in that phase’s PWM comparator. The offset is in a direction
to reduce the imbalance.
The balancing circuit can not make up for a difference in
r
higher r
reduced.
Figures 8 and 9 show the inductor current of a two phase
system without and with current balancing.
Inductor Current
The inductor current in each phase of a multi-phase Buck
converter has two components. There is a current equal to
the load current divided by the number of phases (I
and a sawtooth current, (i
The sawtooth component is dependent on the size of the
inductors, the switching frequency of each phase, and the
values of the input and output voltage. Ignoring secondary
effects, such as series resistance, the peak to peak value of
the sawtooth current can be described by:
i
Where: V
Example: For V
Then i
PK-PK
DS(ON)
IN
IN
should be selected to give the desired “droop” voltage at
= Vdroop / 50µA
PK-PK
= (V
DS(ON)
between synchronous rectifiers. If a FET has a
CORE
IN
F
IN
V
= 4.3A
SW
x V
.
IN
, the current through that phase will be
L = value of the inductor
CORE
F
CORE
= DC value of the output or V
= DC value of the input or supply voltage
= switching frequency
V
SW
IN
L = 1.3µH,
= 1.6V,
= 12V,
= 250kHz,
- V
IN
PK-PK
ISEN
CORE
= 1.6kΩ
12
” above).
) resulting from switching.
2
FB
) / (L x F
and Cc, are scaled in
SW
x V
ID
voltage
IN
LT
)
/ n),
ISEN
HIP6302
HIP6302
The inductor, or load current, flows alternately from V
through Q1 and from ground through Q2. The HIP6302
samples the on-state voltage drop across each Q2 transistor
to indicate the inductor current in that phase. The voltage
drop is sampled 1/3 of a switching period, 1/F
turned OFF and Q2 is turned on. Because of the sawtooth
current component, the sampled current is different from the
average current per phase. Neglecting secondary effects,
the sampled current (I
current (I
I
Where: I
Example: Using the previously given conditions, and
For I
Then I
SAMPLE
FIGURE 8. TWO CHANNEL MULTIPHASE SYSTEM WITH
FIGURE 9. TWO CHANNEL MULTIPHASE SYSTEM WITH
LT
25
20
15
10
5
0
n = 2
SAMPLE
25
20
15
10
5
0
LT
LT
= 50A,
= I
n = the number of channels
) by:
LT
CURRENT BALANCING DISABLED
CURRENT BALANCING ENABLED
= total load current
/ n + (V
= 25.49A
IN
SAMPLE
V
CORE
) can be related to the load
- 3V
CORE
2
) / (6L x F
SW
December 27, 2004
, after Q1 is
SW
IN
FN4766.3
x V
IN
)