HIP6302VCB-T Intersil, HIP6302VCB-T Datasheet - Page 7

• Manufacturer Part Number: HIP6302VCB-T
• Description: IC CTRLR PWM MULTIPHASE 16-SOIC
• Manufacturer: Intersil

Specifications of HIP6302VCB-T

• Pwm Type: Controller
• Number Of Outputs: 4
• Frequency - Max: 336kHz
• Voltage - Supply: 4.75 V ~ 5.25 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 16-SOIC (3.9mm Width)
• Frequency-max: 336kHz
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Duty Cycle: -

Absolute Maximum Ratings
Supply Voltage, V
Input, Output, or I/O Voltage . . . . . . . . . . GND -0.3V to V
Recommended Operating Conditions
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5%
Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty..
NOTES:
Electrical Specifications
INPUT SUPPLY POWER
Input Supply Current
POR (Power-On Reset) Threshold
REFERENCE AND DAC
System Accuracy
DAC (VID0 - VID3) Input Low Voltage DAC Programming Input Low Threshold Voltage
DAC (VID0 - VID3) Input High Voltage DAC Programming Input High Threshold Voltage
VID Pull-Up
CHANNEL GENERATOR
Frequency, F
Disable Voltage
ERROR AMPLIFIER
DC Gain
Gain-Bandwidth Product
Slew Rate
Maximum Output Voltage
Minimum Output Voltage
I
Full-Scale Current Level
Overcurrent Trip Level
POWER-GOOD MONITOR
Undervoltage Threshold
Undervoltage Threshold
PGOOD Low Output Voltage
PROTECTION
Overvoltage Threshold
Overvoltage Hysteresis
1. θ
2. VID input levels above 2.9V may produce an reference-voltage offset inaccuracy.
3. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested.
SEN
JA
is measured with the component mounted on a high effective thermal conductivity test board in free air. (See Tech Brief TB379 for details.)
PARAMETER
SW
CC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7V
7
Operating Conditions: V
R
V
V
Percent system deviation from programmed VID Codes
VIDx = 0V or VIDx = 2.5V (Note 2); Not tested - for reference only
R
V
R
C
C
R
R
Not tested - for reference, only
Not tested - for reference, only
VSEN Rising
VSEN Falling
I
VSEN Rising
VSEN Falling; Not tested - for reference, only
PGOOD
CC
CC
FS/DIS
T
T
L
L
L
L
L
= 100kΩ
= 10k to ground
= 100pF, R
= 100pF, R
= 10k to ground
= 10k to ground
= 100kΩ, ±1%
Rising
Falling
to disable controller; Not tested - for reference, only
= 4mA
L
L
= 10k to ground
= 10k to ground
HIP6301V, HIP6302V
HIP6301V, HIP6302V
CC
CC
+ 0.3V
TEST CONDITIONS
= 5V, T
A
= +0°C to +70°C, Unless Otherwise Specified.
Thermal Information
Thermal Resistance (Typical, Note 1)
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
16 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
20 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
(Note 3)
MIN
4.25
3.75
1.12
-0.8
224
2.0
3.6
10
-
-
-
-
-
-
-
-
-
-
-
-
-
TYP
4.38
3.88
82.5
0.92
0.90
1.15
280
5.3
72
18
50
2
-
-
-
-
-
-
-
-
-
(Note 3)
MAX
4.00
1.20
336
4.5
0.8
0.8
1.0
0.5
0.4
15
40
-
-
-
-
-
-
-
-
-
-
θ
JA
May 5, 2008
UNITS
V
V
V
FN9034.3
(°C/W)
70
65
MHz
V/µs
kHz
mA
µA
µA
µA
dB
DAC
DAC
DAC
%
%
V
V
V
V
V
V
V
V