LT1959CR#TRPBF Linear Technology, LT1959CR#TRPBF Datasheet - Page 7

• Manufacturer Part Number: LT1959CR#TRPBF
• Description: IC SW REG STEP-DWN 500KHZ 7-DD
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LT1959CR#TRPBF

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: 1.21 ~ 38 V
• Current - Output: 4.5A
• Frequency - Switching: 500kHz
• Voltage - Input: 4.3 ~ 15 V
• Operating Temperature: 0°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: D²Pak, TO-263 (7 leads + tab)
• Dc To Dc Converter Type: Step Down
• Pin Count: 7 +Tab
• Input Voltage: 16V
• Output Voltage: 1.21 to 2.42V
• Switching Freq: 540kHz
• Output Current: 8.5A
• Package Type: DDPAK
• Output Type: Adjustable
• Switching Regulator: Yes
• Line Regulation: 0.03%/V
• Mounting: Surface Mount
• Input Voltage (min): 4V
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Compliant

BLOCK
The LT1959 is a constant frequency, current mode buck
converter. This means that there is an internal clock and
two feedback loops that control the duty cycle of the power
switch. In addition to the normal error amplifier, there is a
current sense amplifier that monitors switch current on a
cycle-by-cycle basis. A switch cycle starts with an oscilla-
tor pulse which sets the R
When switch current reaches a level set by the inverting
input of the comparator, the flip-flop is reset and the
switch turns off. Output voltage control is obtained by
using the output of the error amplifier to set the switch
current trip point. This technique means that the error
amplifier commands current to be delivered to the output
rather than voltage. A voltage fed system will have low
phase shift up to the resonant frequency of the inductor
INPUT
SHDN
SYNC
COMPARATOR
SHUTDOWN
DIAGRAM
REGULATOR
2.9V BIAS
2.38V
3.5 A
0.4V
LOCKOUT
COMPARATOR
S
W
flip-flop to turn the switch on.
SLOPE COMP
OSCILLATOR
INTERNAL
V
CC
500kHz
+
0.01
V
Figure 1. Block Diagram
0.9V
–
FOLDBACK
C
CURRENT
+
–
CLAMP
LIMIT
CURRENT
SENSE
AMPLIFIER
VOLTAGE GAIN = 20
CURRENT
COMPARATOR
Q2
and output capacitor, then an abrupt 180 shift will occur.
The current fed system will have 90 phase shift at a much
lower frequency, but will not have the additional 90 shift
until well beyond the LC resonant frequency. This makes
it much easier to frequency compensate the feedback loop
and also gives much quicker transient response.
High switch efficiency is attained by using the BOOST pin
to provide a voltage to the switch driver which is higher
than the input voltage, allowing switch to be saturated.
This boosted voltage is generated with an external capaci-
tor and diode. Two comparators are connected to the
shutdown pin. One has a 2.38V threshold for undervoltage
lockout and the second has a 0.4V threshold for complete
shutdown.
S
R
g
SHIFT CIRCUIT
m
FREQUENCY
FLIP-FLOP
= 2000 Mho
AMPLIFIER
R
S
ERROR
–
+
CIRCUITRY
DRIVER
1.21V
BOOST
PARASITIC DIODES
DO NOT FORWARD BIAS
LT1959
Q1
POWER
SWITCH
1959 BD
GND
V
FB
SW
7