EL7554IREZ-T13 Intersil, EL7554IREZ-T13 Datasheet - Page 9

• Manufacturer Part Number: EL7554IREZ-T13
• Description: IC REG 4A DC/DC STEP-DN 28HTSSOP
• Manufacturer: Intersil
• Type: Step-Down (Buck)r

Specifications of EL7554IREZ-T13

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 0.8 ~ 6 V
• Current - Output: 4A
• Frequency - Switching: 370kHz
• Voltage - Input: 3 ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP Exposed Pad, 28-eTSSOP, 28-HTSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

Waveforms
V
Detailed Description
The EL7554 is a full-feature synchronous 6A step-down
regulator capable of up to 96% efficiency. This device
operates from 3V to 6V V
CMOS power FETs, the device can operate at up to 100%
duty ratio, allowing for output voltage range from 0.8V up to
nearly V
1MHz enables the use of small components, making the
whole converter occupy less than 0.58 square inch with
components on one side of the PCB. The EL7554 operates
at constant frequency PWM mode, making external
synchronization possible. Patented on-chip resistorless
current-sensing enables current mode control, which
provides over-current protection, and excellent step load
response. The EL7554 features soft-start and full start-up
control, which eliminate the in-rush current and enables
users to control the start-up of multiple converters to any
configuration with ease. The EL7554 also offers a ±5%
voltage margining capability that allows raising and lowering
of the supplies derived from the EL7554 to validate the
performance and reliability of system cards quickly and
easily during manufacturing testing. A junction temperature
indicator conveniently monitors the silicon die temperature,
saving designers time in the tedious thermal
characterization.
Start-Up
The EL7554 employs a special soft-start to suppress the in-
rush current (see Figure 12). The start-up process takes
about 2ms and begins when the input voltage reaches about
2.8V and EN pin voltage 2V. When EN is released from
LOW, or the converter comes out of thermal shut-down
mode, the soft-start process repeats. When the input voltage
ramps up too slowly, slight over- current at the input can
allows 100% turn-on of the upper PFET switch, achieving
IN
= V
D
IN
= 3.3V, V
.The adjustable high switching frequency of up to
FIGURE 18. ADJUSTABLE START-UP
O
(Continued)
= 1.8V, I
2ms/DIV
IN
O
input supply. With internal
= 4A, L = 2.2µH, C
9
C
C
IN
OUT
= 100µF,
= 150µF
IN
= 2x10µF, C
V
I
V
IN
IN
O
(2A/DIV)
(1V/DIV)
(2V/DIV)
OUT
EL7554
= 47µF, C
occur. Connecting a small capacitor at EN will delay the
start-up. The delay time T
where:
• C
• V
• I
If a slower than 2ms soft start-up is needed, please refer to
Full Start-Up Control section.
Steady-State Operation
The converter always operates at fixed frequency
continuous-conduction mode. For fast transient response,
peak current control method is employed. The inductor
current is sensed from the upper PFET. This current signal,
the slope compensation, and the compensated error signal
are fed to the PWM comparator to generate the PWM signal
for the internal power switches. When the upper PFET is on,
the low-side NFET is off and input voltage charges the
inductor. When PFET is off, the NFET is on and energy
stored in the inductor is dumped to the output to maintain
constant output voltage. Therefore, the LX waveform is
always a stable square waveform (see Figure 13) with peak
close to V
operating properly.
100% Duty Ratio
EL7554 uses CMOS as internal synchronous power
switches. The upper switch is a PMOS and the lower switch
an NMOS. This not only saves a boot capacitor, it also
T
OSC
D
see Figure 5)
EN
EN_HI
EN
=
= 220pF, T
C
is the EN pin pull-up current, nominal 2.5µA
is the capacitance at EN pin
EN
IN
is the EN input high level (function of V
×
. So LX is a good indication that the converter is
V
------------------- -
FIGURE 19. TRACKING START-UP
EN_HI
I
EN
A
= +25°C unless otherwise noted.
5ms/DIV
D
can be calculated by:
C
C
IN
OUT
= 100µF,
= 150µF
November 5, 2007
V
V
V
DD
IN
O1
O2
(5V/DIV)
=2.5V
=1.8V
voltage,
FN7360.5