ISL6142/52EVAL1 Intersil, ISL6142/52EVAL1 Datasheet
ISL6142/52EVAL1
Specifications of ISL6142/52EVAL1
Related parts for ISL6142/52EVAL1
ISL6142/52EVAL1 Summary of contents
Page 1
... RL = Equivalent load resistance TM Electronic Circuit Breaker distinguishes provides a scaled version of the load current to -V provides current to OUT IN | Intersil (and design registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved Endura™ trademark of Intersil Americas Inc. AN1000 ...
Page 2
... IS NOTE: See www.intersil.com/hotplug for more information. Fully populated; requires only 48V and 5Vpower supplies to exercise all IC functions ISL6142/52 Evaluation Board Overview This document assumes the reader is familiar with the hot plug concept, and has a copy of the ISL6142/52 data sheet (FN9086) ...
Page 3
... JP1A and JP1B on the Control board must be removed to enable the short pin ground configuration. CONTROL Board (IC Hot-Plug; Fig. 7) • Two hot plug channels • Compare Intersil ISL6142 (L) to ISL6152 (H) • Easily change application components and evaluate circuit performance with the socketed through hole components of channel B • ...
Page 4
Footprints for DRAIN protection diodes (channel B). Board is shipped with a zero ohm resistor in the D2B place holder. • Footprint for over voltage clamping suppressor (channel B) • Option for green LED for Power Good OK (ISL6142 ...
Page 5
Current threshold of 185mA (0.05V/0.27ohm = 185 mA). The FET should turn off, the A/B ON LED should go off, the fault LED’s D5B and D6B should both turn on. For the ISL6152, D6A will turn on (D5A will always ...
Page 6
... R10 = 5.1KΩ (10 6.49KΩ (1 150nF (25V) FIGURE 4. TYPICAL APPLICATION U1 is the ISL6142 (L) or ISL6152 (H) Intersil hot plug controller IC; the only difference between the two part numbers is the polarity of the PWRGD/PWRGD output (pin 1). Channel A is populated with the ISL6152; channel B is populated with the ISL6142 ...
Page 7
Voltage (UV) trip points. Reference the ISL6142/52 data sheet for more details. R7, R8, and R9 are used to sense the load current (R7/R8) and convert the scaled output current (IS (R9). This voltage will typically be the input signal ...
Page 8
It is used in some applications to hold the IC’s in reset until all pins are have made good contact. If this is desired, the user must also remove the jumper caps on JP1A and JP1B ...
Page 9
Test Pins • TPPGA (pin A1); PWRGDA • TPPGB (pin A6); PWRGDB • TPG (pin A5 - A2); GND • TPA (also J5A, J5B, J5C); -VOUTA • TPB (also J6A, J6B, J6C); -VOUTB • J7A, J7B, J7C, J8A, J8B, J8C; ...
Page 10
C21A board bottom plane GND C21B top of board -VINB GND Short pin Ground D6 Logic R10 Supply JP2 TP3 SW2 D1* C4* to ADC -48V IN 10 ISL6142/52 EVAL ...
Page 11
ISL6142/52 EVAL boards LOAD (Output) 3 edge connector pins; top 6 edge connector pins; bottom (4 GND; 2 PWRGD or PWRGD) 3 edge connector pins; top 11 -VOUTA A C11A LOAD C12A TPPGA C13A GND C11B TPPGB C12B B C13B ...
Page 12
Bill Of Material Component Name CONTROL BOARD BOM U1 A/B ISL6152 (A); ISL6142 (B) Q1 A/B IRF530 or equivalent Q2 A/B Optional FET Q3 A/B Optional FET R1 A/B Current Sense Resistor R1_alt A/B Current Sense Resistor (alternate) 2512, 20Ω, ...
Page 13
Component Name BUS BOARD BOM C21 A/B Optional Input Capacitor LOAD BOARD BOM R11 A/B Load Resistor R12 A/B Over-Load Resistor R13 A/B LED Current Resistor D11 A/B Red LED SW11 A/B Load Slide Switch SW12 A/B C11 A/B Optional ...
Page 14
Component Placement and Labels TOP 14 FIGURE 9. LOAD BOARD FIGURE 10. CONTROL BOARD BOTTOM ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...