ZX-XF12 Omron, ZX-XF12 Datasheet - Page 13

• Manufacturer Part Number: ZX-XF12
• Description: ATTACHMNT SIDEVIEW ZX-LT1001/005
• Manufacturer: Omron

Specifications of ZX-XF12

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: ZXXF12

*1. The response speed of the linear output is calculated as the measurement period
*2. The output can be switched between a current output and voltage output using a switch on the bottom of the Amplifier Unit.
*3. Setting is possible via the monitor focus function.
*4. A Calculating Unit (ZX-CAL2) is required.
Note:
14
Item
Measurement period
Possible average count settings*1
Temperature characteristic
Linear output*2
Judgement outputs
(3 outputs: HIGH/PASS/LOW)*1
Laser OFF input, zero reset input, timing input,
reset input
Functions
Indications
Power supply voltage
Current consumption
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Vibration resistance
(destruction)
Shock resistance
(destruction)
Connection method
Weight (packed state)
Materials
Accessories
Applicable Amplifier
Units
Current consumption 12 mA max. (supplied from the Smart Sensor Amplifier Unit)
Ambient temperature
Ambient humidity
Connection method
Dielectric strength
Insulation resistance
Vibration resistance
(destructive)
Shock resistance
(destructive)
Materials
Weight (packed state) Approx. 50 g
Accessories
The response speed of the judgement outputs is calculated as the measurement period
Amplifier Units
Calculating Unit
Item
For operating details, refer to the operation manual (Cat. No. Z157).
ZX Series (ZX-L-N)
ZX-LD11-N/41-N, ZX-EDA11/41, ZX-TDA11/41
Operating: 0 to 50 C, Storage: 15 to 60 C (with no icing or con-
densation)
Operating and storage: 35% to 85% (with no condensation)
Connector
1,000 VAC, 50/60 Hz for 1 min
100 M (at 500 VDC)
10 to 150 Hz, 0.7-mm double amplitude 80 min each in X, Y, and
Z directions
300 m/s
ward/backward)
Display: Acrylic, Case: ABS resin
Instruction sheet
2
3 times each in six directions (up/down, left/right, for-
Model
150 s
1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1,024, 2,048, or 4,096
When connected to a Reflective Sensor Head: 0.01% FS/ C, When connected to a Through-beam Sensor Head: 0.1% FS/ C
4 to 20 mA/FS, Max. load resistance: 300
NPN open-collector outputs, 30 VDC, 50 mA max.
Residual voltage: 1.2 V max.
ON: Short-circuited with 0-V terminal or 1.5 V or less
OFF: Open (leakage current: 0.1 mA max.)
Measurement value display, set value/light level/resolution display, scaling, display reverse, display OFF mode, ECO mode, number of display
digit changes, sample hold, peak hold, bottom hold, peak-to-peak hold, self-peak hold, self-bottom hold, intensity mode, zero reset, initial
reset, ON-delay timer, OFF-delay timer, one-shot timer, deviation, previous value comparison, sensitivity adjustment, keep/clamp switch,
direct threshold value setting, position teaching, 2-point teaching, automatic teaching, hysteresis width setting, timing inputs, reset input,
monitor focus, (A-B) calculations*4, (A+B) calculations*4, mutual interference*4, laser deterioration detection, zero reset memory, key lock
Operation indicators: High (orange), pass (green), low (yellow), 7-segment main display (red), 7-segment subdisplay (yellow), laser ON
(green), zero reset (green), enable (green)
12 to 24 VDC 10%, Ripple (p-p): 10% max.
140 mA max. with power supply voltage of 24 VDC (with Sensor connected)
Operating: 0 to 50 C, Storage: 15 to 60 C (with no icing or condensation)
Operating and storage: 35% to 85% (with no condensation)
20 M min. at 500 VDC
1,000 VAC, 50/60 Hz for 1 min
10 to 150 Hz, 0.7-mm double amplitude 80 min each in X, Y, and Z directions
300 m/s
Prewired (standard cable length: 2 m)
Approx. 350 g
Case: PBT (polybutylene terephthalate), Cover: Polycabonate
Instruction sheet
ZX-CAL2
2
3 times each in six directions (up/down, left/right, forward/backward)
Smart Sensors
ZX-LDA11-N
(average count setting + 1) (with fixed sensitivity).
(average count setting + 1) (with fixed sensitivity).
4 V ( 5 V, 1 to 5 V *3), Output impedance: 100
* Contact your OMRON representative for CompoWay/F communi-
cations specifications.
Current consumption
Applicable Amplifier Units ZX Series
Applicable Amplifier Unit
versions
Max. No. of Amplifier Units 5
Commu-
nications
functions
Indicators
Protective circuits
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Materials
Accessories
ZX-series Communications
Interface Unit
Item
Communica-
tions port
Communica-
tions protocol
Baud rate
Data configura-
tion
PNP open-collector outputs, 30 VDC, 50 mA max.
Residual voltage: 2 V max.
ON: Supply voltage short-circuited or supply voltage within 1.5 V
OFF: Open (leakage current: 0.1 mA max.)
60 mA max. (supplied by the Amplifier Unit)
ZX-LDA@1-N Ver. 1.000 or higher
ZX-EDA@1 Ver. 1.100 or higher
ZX-TDA@1 Ver. 1.000 or higher
RS-232C port (9-pin D-Sub Connector)
CompoWay/F*
38,400 bps
Data bits: 8, Parity: none, Start bits: 1, Stop bits: 1, Flow con-
trol: none
Power supply: green, Sensor communications: green, Sen-
sor communications error: red, External terminal communi-
cations: green, External terminal communications error: red
Reverse polarity protection
Operating: 0 to 50 C, storage: 15 to 60 C (with no icing or
condensation)
Operating and storage: 35% to 85% (with no condensation)
20 M min. (at 500 VDC)
1,000 VAC, 50/60 Hz for 1 min, Leakage current: 10 mA
max.
Case: PBT (polybutylene terephthalate), Cover: Polycarbon-
ate
Instruction sheet, 2 clamps
ZX-LDA41-N
ZX-SF11