ZX-XF12 Omron, ZX-XF12 Datasheet - Page 34

• Manufacturer Part Number: ZX-XF12
• Description: ATTACHMNT SIDEVIEW ZX-LT1001/005
• Manufacturer: Omron

Specifications of ZX-XF12

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: ZXXF12

Precautions
Conform to the specified ratings and performance. Refer to the Spec-
ifications for each product on the following pages.
ZX-L: Pages 13 and 14
ZX-E: Pages 21 and 22
ZX-T: Pages 31 and 32
Environment
Do not operate the product in locations subject to flammable or explo-
sive gases.
In order to ensure safe operation and maintenance, do not install the
product in the vicinity of high-voltage devices or power equipment.
This product consists of precision parts that may fail if it is dropped.
Design Precautions
Compatibility
Sensors and Amplifier Units are mutually compatible. Sensors can be
added or replaced individually.
Influence of High-frequency
Electromagnetic Fields
Using the product in the vicinity of devices that generate high-fre-
quency electromagnetic fields, such as ultrasonic cleaning equip-
ment, high-frequency generators, transceivers, mobile phones, and
inverters, may result in malfunction.
Wiring
Wiring Check
After wiring is completed, before turning ON the power, confirm that
the power supply is connected correctly, that there are no faulty con-
nections, such as load short-circuits, and that the load current is cor-
rect. Incorrect wiring may result in failure.
Cable Extension
Do not extend the cable for the Sensor and the Amplifier Unit to a
length exceeding 10 m. Use a ZX-XC@A Extension Cable (sold sep-
arately) to extend the Sensor’s cable. Extend the Amplifier Unit’s ca-
ble using a shielded cable of the same type.
Design Precautions
Correct Use
Wiring
Do not use the product at voltages exceeding the rated values. Doing
so may result in damage.
Do not connect the product to an AC power supply or connect the
power supply in reverse.
Do not short loads connected to open-collector outputs.
Do not lay the cable for the product together with or in the same duet
as high-voltage lines or power lines. Doing so may result in incorrect
operation or damage due to induction.
Other Precautions
Do not attempt to disassemble, repair, or modify the product.
Dispose of the product using standard procedures for industrial
waste.
Do not connect combinations of ZX-L@@-, ZX-E@@-, and ZX-T@@-
series Smart Sensors.
Power Supply
When using a commercially available switching regulator, ground the
FG (frame ground) terminal.
If the power supply line is subject to surges, connect a surge absorber
that meets the conditions of the operating environment.
Calculating Unit
When using a Calculating Unit, connect the linear output ground of
the corresponding Amplifier Unit.
Connectors
Do not connect or disconnect connectors while the power is ON.
Be sure hold to connectors by the cover when connecting or discon-
necting.
Installation Location
Do not install the product in the following locations.
• Locations subject to temperatures outside the specified range
• Locations subject to condensation due to sudden temperature
• Locations subject to humidity levels outside range 35% to 85%
• Locations subject to corrosive or flammable gases
• Locations subject to dust, salts, or metallic powder.
• Locations directly subject to vibrations and shocks
• Locations subject to splashes of water, oil, or chemicals
• Locations subject to strong electromagnetic or electrical fields
Maintenance and Inspection
• Be sure to turn OFF the power supply before adjusting or removing
• Cleaning:
changes
the Sensor Head.
Do not use thinners, benzine, acetone, or kerosene for cleaning.
ZX Series
Smart Sensors
35