ISL83699 Intersil Corporation, ISL83699 Datasheet
ISL83699
Available stocks
Related parts for ISL83699
ISL83699 Summary of contents
Page 1
... This family of parts may be used to “mux-in” additional functionality while reducing ASIC design risk. The ISL83699 is offered in small form factor packages, alleviating board space limitations. The ISL83699 consists of four SPDT switches configured as a dual double-pole/double-throw (DPDT) device with two logic control inputs that control two SPDT switches each ...
Page 2
... NO1 1 16 COM1 2 15 NC1 3 14 IN1 NO2 5 12 COM2 NC2 7 GND 8 9 ISL83699 (3x3 QFN) TOP VIEW NC1 2 IN1-2 3 NO2 4 COM2 NOTE: 1. Switches Shown for Logic “0” Input. Truth Table LOGIC ...
Page 3
... Maximum Junction Temperature (Plastic Package 150°C Maximum Storage Temperature Range -65°C to 150°C Maximum Lead Temperature (Soldering 10s 300°C (Lead Tips Only) Operating Conditions Temperature Range ISL83699IX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C Test Conditions +2.7V to +3.3V, GND = 0V, V Unless Otherwise Specified TEST CONDITIONS = 100mA ...
Page 4
... Crosstalk (Channel-to-Channel 50Ω (See Figure OFF Capacitance 1MHz, V OFF COM ON Capacitance 1MHz, V COM(ON) 4 ISL83699 Test Conditions +2.7V to +3.3V, GND = 0V, V Unless Otherwise Specified (Continued) TEST CONDITIONS 0V, (See Figure COM 0V, (See Figure 7) ...
Page 5
... SWITCH ∆V OUT OUTPUT V OUT ON LOGIC OFF INPUT Q = ∆ OUT L FIGURE 2A. MEASUREMENT POINTS 5 ISL83699 Test Conditions +1.65V to +2V, GND = 0V, V Unless Otherwise Specified (Continued) TEST CONDITIONS = (Note < 5ns r t < 5ns f OUT LOGIC 90% INPUT Repeat test for all switches. C capacitance ...
Page 6
... ANALYZER GND R L FIGURE 4. OFF ISOLATION TEST CIRCUIT SIGNAL GENERATOR COM ANALYZER GND R L FIGURE 6. CROSSTALK TEST CIRCUIT 6 ISL83699 (Continued LOGIC 90% INPUT includes fixture and stray capacitance. L FIGURE 3. BREAK-BEFORE-MAKE TIME ...
Page 7
... CMOS analog switches, in that they have two supply pins: V+ and GND. V+ and GND drive the internal CMOS switches and set their analog voltage limits. Unlike switches with a 4V maximum supply voltage, the ISL83699 4.7V maximum supply voltage provides plenty of room for the 10% tolerance of 3.6V supplies, as well as room for overshoot and noise spikes ...
Page 8
... COM FIGURE 11. ON RESISTANCE vs SWITCH VOLTAGE 8 ISL83699 V+ or GND and the analog signal. This means their leakages will vary as the signal varies. The difference in the two diode leakages to the V+ and GND pins constitutes the analog- signal-path leakage current. All analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal ...
Page 9
... IN P-P P FREQUENCY (MHz) FIGURE 15. FREQUENCY RESPONSE 1.5 1.4 1.3 1.2 1.1 V INH 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 1 1 (V) FIGURE 17. DIGITAL SWITCHING POINT vs SUPPLY VOLTAGE 9 ISL83699 T = 25°C, Unless Otherwise Specified (Continued 3.5 4 4.5 -10 -20 -30 -40 -50 0 -60 20 -70 40 -80 60 -90 80 -100 100 -110 100 600 Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): ...
Page 10
... Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimen- sions are not necessarily exact. (Angles in degrees) 10 ISL83699 M16.173 16 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE ...
Page 11
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11 ISL83699 L16.3x3 16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE C ...