PIC24HJ64GP506-I/PT Microchip Technology, PIC24HJ64GP506-I/PT Datasheet - Page 11

• Manufacturer Part Number: PIC24HJ64GP506-I/PT
• Description: IC PIC MCU FLASH 32KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP506-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (22K x 24)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 53
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: 3-Wire/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 13
• Operating Supply Voltage: 0 V to 2.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 18-ch x 12-bit
• Controller Family/series: PIC24
• No. Of I/o's: 53
• Ram Memory Size: 8KB
• Cpu Speed: 40MIPS
• No. Of Timers: 13
• Embedded Interface Type: CAN, I2C, SPI, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDDM300024 - KIT DEMO DSPICDEM 1.1MA240012 - MODULE PLUG-IN PIC24H 100QFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM300019 - BOARD DEMO DSPICDEM 80L STARTERDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

9. Module: SPI
10. Module: ECAN
11. Module: ECAN
© 2010 Microchip Technology Inc.
The SMP bit (SPIxCON1<9>, where x = 1 or 2)
does not have any effect when the SPI module is
configured for a 1:1 prescale factor in Master
mode. In this mode, whether the SMP bit is set or
cleared, the data is always sampled at the end of
data output time.
Work around
If sampling at the middle of data output time is
required, then configure the SPI module to use a
clock prescale factor other than 1:1, using the
PPRE<1:0>
SPIxCON1 register.
Affected Silicon Revisions
If any buffers other than Buffer 0 are enabled as
transmit buffers (i.e., if the TXEN bits other than
TXEN0 are set to ‘1’), incorrect ID and data
transmissions will occur intermittently.
Work around
Enable only Buffer 0 for transmission.
Affected Silicon Revisions
Under specific conditions, the first five bits of a
transmitted identifier may not match the value in
the transmit buffer SID. If the ECAN module
detects a Start-of-Frame (SOF) in the third bit of
interframe space, and if a message to be
transmitted is pending, the first five bits of the
transmitted identifier may be corrupted.
Work around
None.
Affected Silicon Revisions
A2
A2
A2
X
X
X
A3
A3
A3
X
X
X
A4
A4
A4
and
X
X
X
SPRE<2:0>
bits
in
the
PIC24HJXXXGPX06/X08/X10
12. Module: ECAN
13. Module: I
14. Module: ADC
The ECAN module (ECAN1 or ECAN2) does not
function correctly in Loopback mode.
Work around
Do not use Loopback mode.
Affected Silicon Revisions
The Bus Collision Status bit (BCL) is not set when
a bus collision occurs during a Restart or Stop
event. However, the BCL bit is set when a bus
collision occurs during a Start event.
Work around
None.
Affected Silicon Revisions
ADC event triggers from the INT0 pin will not
wake-up the device from Sleep or Idle mode if the
SMPI bits are non-zero. That is, if the ADC is
configured to generate an interrupt after a certain
number of INT0 triggered conversions, the ADC
conversions will not be triggered and the device
will remain in Sleep. The ADC will perform
conversions and wake-up the device only when it
is configured to generate an interrupt after each
INT0 triggered conversion (SMPI<3:0> = 0000).
Work around
None. If an ADC event trigger from the INT0 pin is
required, initialize SMPI<3:0> to ‘0000’ (interrupt
on every conversion).
Affected Silicon Revisions
A2
A2
A2
X
X
X
A3
A3
A3
X
X
X
2
C
A4
A4
A4
X
X
X
DS80444D-page 11