PIC24HJ64GP506-I/PT Microchip Technology, PIC24HJ64GP506-I/PT Datasheet - Page 13

• Manufacturer Part Number: PIC24HJ64GP506-I/PT
• Description: IC PIC MCU FLASH 32KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP506-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (22K x 24)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 53
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: 3-Wire/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 13
• Operating Supply Voltage: 0 V to 2.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 18-ch x 12-bit
• Controller Family/series: PIC24
• No. Of I/o's: 53
• Ram Memory Size: 8KB
• Cpu Speed: 40MIPS
• No. Of Timers: 13
• Embedded Interface Type: CAN, I2C, SPI, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDDM300024 - KIT DEMO DSPICDEM 1.1MA240012 - MODULE PLUG-IN PIC24H 100QFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM300019 - BOARD DEMO DSPICDEM 80L STARTERDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

21. Module: UART
22. Module: UART
23. Module: I
© 2010 Microchip Technology Inc.
The auto-baud feature may not calculate the correct
baud rate when the High Baud Rate Enable bit,
BRGH, is set. With the BRGH bit set, the baud rate
calculation used is the same as BRG = 0.
Work around
If the auto-baud feature is needed, use the Low
Baud Rate mode by clearing the BRGH bit.
Affected Silicon Revisions
With the auto-baud feature selected, the Sync
Break character (0x55) may be loaded into the
FIFO as data.
Work around
To prevent the Sync Break character from being
loaded into the FIFO, load the UxBRG register with
either 0x0000 or 0xFFFF prior to enabling the
auto-baud feature (ABAUD = 1).
Affected Silicon Revisions
Writing to I2CxTRN during a Start bit transmission
generates a write collision, indicated by the
IWCOL bit (I2CxSTAT<7>) being set. In this state,
additional writes to the I2CxTRN register should
be blocked. However, in this condition, the
I2CxTRN register can be written, although
transmissions will not occur until the IWCOL bit is
cleared in software.
Work around
After each write to the I2CxTRN register, read the
IWCOL bit to ensure a collision has not occurred.
If the IWCOL bit is set, it must be cleared in
software, and I2CxTRN register must be rewritten.
Affected Silicon Revisions
A2
A2
A2
X
X
X
A3
A3
A3
X
X
X
2
C
A4
A4
A4
X
X
X
PIC24HJXXXGPX06/X08/X10
24. Module: I
25. Module: I
The ACKSTAT bit (I2CxSTAT<15>) reflects the
received
transmissions, but not for slave transmissions. As
a result, a slave cannot use this bit to determine
whether it received an ACK or a NACK from a
master. In future silicon revisions, the ACKSTAT
bit will reflect received ACK/NACK status for both
master and slave transmissions.
Work around
The SDA pin should be connected to any other
available I/O pin on the device. After transmitting a
byte, the slave should poll the SDA line (subject to
a time-out period that is dependent on the
application) to determine whether an ACK (‘0’) or
a NACK (‘1’) was received.
Affected Silicon Revisions
The D_A Status bit (I2CxSTAT<5>) is set on a
slave data reception in the I2CxRCV register, but
is not set on a slave write to the I2CxTRN register.
In future silicon revisions, the D_A bit will be set on
a slave write to the I2CxTRN register.
Work around
Use the D_A Status bit for determining slave
reception status only. Do not use it for determining
slave transmission status.
Affected Silicon Revisions
A2
A2
X
X
A3
A3
X
X
2
2
ACK/NACK
C
C
A4
A4
X
X
status
DS80444D-page 13
for
master