PIC24HJ64GP506-I/PT Microchip Technology, PIC24HJ64GP506-I/PT Datasheet - Page 12

• Manufacturer Part Number: PIC24HJ64GP506-I/PT
• Description: IC PIC MCU FLASH 32KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP506-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (22K x 24)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 53
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: 3-Wire/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 13
• Operating Supply Voltage: 0 V to 2.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 18-ch x 12-bit
• Controller Family/series: PIC24
• No. Of I/o's: 53
• Ram Memory Size: 8KB
• Cpu Speed: 40MIPS
• No. Of Timers: 13
• Embedded Interface Type: CAN, I2C, SPI, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDDM300024 - KIT DEMO DSPICDEM 1.1MA240012 - MODULE PLUG-IN PIC24H 100QFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM300019 - BOARD DEMO DSPICDEM 80L STARTERDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24HJXXXGPX06/X08/X10
15. Module: Doze Mode
16. Module: JTAG
17. Module: UART
DS80444D-page 12
None of the following error traps will wake-up a
device from Doze mode: the address error trap,
stack error trap, math error trap or the DMA error
trap.
Work around
None.
Affected Silicon Revisions
JTAG programming does not work.
Work around
None.
Affected Silicon Revisions
With the parity option enabled, a parity error, as
indicated by the PERR bit (UxSTA<3>) being set,
may occur if the Baud Rate Generator contains an
odd value. This affects both of the even and odd
parity options.
Work around
Load the Baud Rate Generator register, UxBRG,
with an even value, or disable the peripheral’s
parity option by loading either 0b00 or 0b11 into
the Parity and Data Selection bits, PDSEL<1:0>
(UxMODE<2:1>).
Affected Silicon Revisions
A2
A2
A2
X
X
X
A3
A3
A3
X
X
X
A4
A4
A4
X
X
X
18. Module: UART
19. Module: UART
20. Module: UART
The Receive Buffer Overrun Error Status bit,
OERR (UxSTA<1>), may be set before the UART
FIFO has overflowed. After the fourth byte is
received by the UART, the FIFO is full. The OERR
bit should set after the fifth byte has been received
in the UART shift register. Instead, the OERR bit
may set after the fourth received byte with the
UART Shift register empty.
Work around
After four bytes have been received by the UART,
the UART Receiver Interrupt Flag bit, U1RXIF
(IFS0<11>) or U2RXIF (IFS1<14>), will be set,
indicating the UART FIFO is full. The OERR bit
may also be set. After reading the UART receive
buffer, UxRXREG, four times to clear the FIFO,
clear both the OERR and UxRXIF bits in software.
Affected Silicon Revisions
UART receptions may be corrupted if the Baud
Rate Generator is set up for 4x mode (BRGH = 1).
Work around
Use the 16x baud rate option (BRGH = 0) and
adjust the baud rate accordingly.
Affected Silicon Revisions
The UTXISEL0 bit (UxSTA<13>) is always read as
zero, regardless of the value written to it. This will
affect read-modify-write operations, such as
bitwise or shift operations. Using a read-modify-
write instruction on the UxSTA register (e.g., BSET,
BLCR) will always write the UTXISEL0 bit to zero.
Work around
If a UTXISEL0 value of ‘1’ is needed, avoid using
read-modify-write instructions on the UxSTA
register.
Copy the UxSTA register to a temporary variable
and set UxSTA<13> prior to performing read-
modify-write operations. Copy the new value back
to the UxSTA register.
Affected Silicon Revisions
A2
A2
A2
X
X
X
A3
A3
A3
X
X
X
A4
A4
A4
X
X
X
© 2010 Microchip Technology Inc.